Jump to content
SAU Community

Recommended Posts

wrecking s1.5 and s2 r33 skylines heaps of parts have complete motor 5speed gearbox and loom ecu good condition 2900 ono,s1 motor unknown condition 600$,seats,boot with mspec wing,sideskirts,deep dished wheels 17-9 1390$ manual conversion 1400$,heaps of other parts,s2 airbag kit,have near complete 33 needs dash put back in and interior and dash loom i have all these parts want 4100$ for complete car.i dont come on here much so best to call or txt 0414333538 located at tweed heads

passenger front headlights, driver side stone guard?

Got any of the above parts im after?

got light but it is onm the near complete car so dont really wanto pull it off just yet

Hello, got a standard r33 gtst airbox?

Thanks

wrecking s1.5 and s2 r33 skylines heaps of parts have complete motor 5speed gearbox and loom ecu good condition 2900 ono,s1 motor unknown condition 600$,seats,boot with mspec wing,sideskirts,deep dished wheels 17-9 1390$ manual conversion 1400$,heaps of other parts,s2 airbag kit,have near complete 33 needs dash put back in and interior and dash loom i have all these parts want 4100$ for complete car.i dont come on here much so best to call or txt 0414333538 located at tweed heads
wrecking s1.5 and s2 r33 skylines heaps of parts have complete motor 5speed gearbox and loom ecu good condition 2900 ono,s1 motor unknown condition 600$,seats,boot with mspec wing,sideskirts,deep dished wheels 17-9 1390$ manual conversion 1400$,heaps of other parts,s2 airbag kit,have near complete 33 needs dash put back in and interior and dash loom i have all these parts want 4100$ for complete car.i dont come on here much so best to call or txt 0414333538 located at tweed heads

I need a rb25 clutch master from a r33 and need it now. I will take 2 if you have them both. Anyways please get back to me asap with pricing and i will pay immediately.

this is the one that bolts off the fire wall not the one off the gear box. I have had many people mix this up within the past couple of days, just want to be clear

do you still have the good condition motor and gearbox? if you do how much for them and how many kms has the motor and box done? is it a complete motor with turbo? what series is it?

  • 3 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Wife wanted basket things in the wardrobe in our temporary house. Thought about ripping our the wardrobe and fitting the entire IKEA set, but it's a temporary house and we want to move in a few years. So IKEA advertises this as a 50cm unit, however the actually basket and rails measure 46cm wide. Only issue was depth, IKEA stuff is quite deep, where as the builder special junk is super shallow at less than 40cm. Send it, chopped the rails, then offset the mounting holes, job done, happy wife, less shit scattered all over the bedroom. Did the same to the other side too. Also drove the Skyline shit box today, dropped off oil at Supercheap Auto. I didn't realise they only now take max 2x bottles per visit. I visited 2x Supercheap Autos.  
    • I've seen similar actually in my situation. You never know what tables are attempted to be used when the car thinks it's -99C or +200C. The fail state is not usually that extreme but you know what I mean - it was in my case though! This is where being able to read all the sensors is useful cause you see this stuff really quickly.
    • The above is very important. However as long as you keep timing relatively low, it's plausible to make your own knock ears and plausible to learn to tune with a modern ECU that can do wideband O2 correction like a boost controller. I mean if you only have one viable road to even drive the car on, learning to tinker to this level may be worth doing given you can't do much else with the car...?
    • I find the fact that the rear plate has to be bent inwards at the rear not so bad: but the front is just awful: It's like come on. (these are my very old, now retired/turned in plates) TBH it is a lot of money to fix a minor issue, the fact I said "I'll never really spend the money on doing this" is why people ended up buying them as a gift for a 'car guy' who can be hard to shop for.. for car guy things.
    • I just bent the ends of my premo plates. It even went through Regency like that after the engine conversion and the inspector (a great bloke!) just squinted his eyes and said "I didn't see that". Plates, and how they look, are just something that have zero importance to me.
×
×
  • Create New...