Jump to content
SAU Community

Recommended Posts

My friend says in the txt i got.....

"I f**ked up the axle on my back left tyre and the rims f**ked. Wonder if SAU knew good people that could fix it and do up the other stuff that needs to be done. Going over the the island in the middle of the road f**ked it"

She wants to know where she can take it to get it repaired and what it might cost.

Link to comment
https://www.sau.com.au/forums/topic/329251-friend-needs-her-s14-repaired/
Share on other sites

  • Replies 52
  • Created
  • Last Reply

Top Posters In This Topic

Here's the only pic i have. She says you can't see the damage with the wheel off but she says something bends as the wheel goes forwards but clicks when you reverse. She lives in Noarlunga Downs. And NO you'r not getting pics of her.

dude, as i said when you asked me on fb, get her to take it to a workshop and have them diagnose it, itll cost her 20 bones to find out. its pretty hard to figure it out based on a couple pictures taken with a mobile phone.

dude, as i said when you asked me on fb, get her to take it to a workshop and have them diagnose it, itll cost her 20 bones to find out. its pretty hard to figure it out based on a couple pictures taken with a mobile phone.

Yeah i think she's going to take it.

the cast spider hub is broken... to break that its taken a pretty big hit and few or the arms are probably gone also, you could get all those parts and a drive shaft for maybe $250 - I would have them if you need them. You might also need the wheel bearings - another $100.

The thing you need to take a closer look at though is if the sub frame has been bent also, if it had been its a lot more work to replace.

If you go to a workshop I would estimate $500 minimum - but quite possibly up to 2k if they have to repair the sub-frame etc as there could be a full day of labor, all the arms, the strut, wheel bearing assembly, drive shaft etc.

Edited by samstain

how exactly did you punt it into a traffic island?

the cast spider hub is broken...

ha. no shit. only just noticed that. good eye. mustve smacked that island pretty hard.

Edited by scandyflick

was at a stop sign onto a main road and in 1st gear. i accellerated around the corner and it spun out one way. then i tried to straighten it up and it did like 2 full 360's across the main road into on coming traffice (while having my foot on accelerater instead of break)...and the island stopped the car heaps suddenly and took a chunk out of the rim and popped the tyre...the car looks fine and everything... no one got hit...its just the wheel part on the back left of my car

It may 'look fine and everything' but do not drive it anywhere - the main arm that locates the wheel has snapped clean off...

Probably they easiest way to fix it is to pick up a complete hub to hub sub-frame and drop it in there.

There is something strange about the colors in the photo, almost looks like the cast part has been cracked for a long time and gone rusty.

i cant drive it at all...the front two wheels are straight andd the back right but the left one...anytime we tried to move it the spare wheels bent inwards like it was trying to go under the car...but then when we reversed it, it clicked back straight :S

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Cheers. Skyline is back on the menu, can’t get rid of it. It’s like a child you don’t want, or herpes 
    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
×
×
  • Create New...