Jump to content
SAU Community

Radiator Upgrades For Rs4

chef_stagea
 Share

Recommended Posts

KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted

Go to a Natrad agent - they should be able to find a generic core with the water and auto connections in the right places

and which is thicker than stock.

All the information on the auto trans cooler is in the DIY section above - you may be able to get a S2 cooler off someone who has gone manual or get one from supa cr*p.

kidafa Veteran

kidafa

Posted
Posted

No point Adam, not like your cars seeing track work or anything anyway. And with the Auto you NEED the oil tank in the bottom the radiator to warm up the fluid in the first place and keep it at a consistent temperature.

-RBD2- Mentor

-RBD2-

Posted
Posted

You don't need the auto tank if you go manual hey chris.....

Why don't you chop a huge hole in your bonnet then v-mount your radiator

Hey Adam,wen you free to roll my guards?

You know,like,properly n shit

Tangles Grand Master

Tangles

Posted
Posted

Ive got a guard roller, come over sometime. Cost me a cpl hundrey on ebay, not used yet (will use this week - awaiting extended wheel studs to fit my wheels around the larger wilwood calipers)

got a supercheap heat gun too, to heat the wheel arch paint so it doesnt (well, less likely to) chip

for radiator, I went to natrad about 4yrs ago for a Koyo radiator, slightly thicker than stock.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Murray_Calavera
      Steps to DIY sanding car back ready for respray....

      By Murray_Calavera · Posted

      Did you panel beat the dents or have you tried to repair this only using filler?  Is your sanding block soft/flexible and is following the shape of the panel rather then just knocking down the high points? 
    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      I haven't knocked them down yet. I think I made the repair more complex than it should have been. I had rock chips combined with waviness and dents and I tackled it all in one because it was near each other and just end up wasting a bunch of bog lol. I'll knock down those areas and see how I go. And yep what you are saying at the end is correct. I think I might be sanding the top of a steep hill then my sanding block falls into the dent and gets rid of the guidecoat if that makes sense. Though shouldnt unless I'm covering too big of an area with not a long enough block. I'll try something new and provide some updates. Getting there though! Thanks as always.  
    • Murray_Calavera
      Steps to DIY sanding car back ready for respray....

      By Murray_Calavera · Posted

      Yeah makes sense, hard to comment on your situation without seeing what your doing. I was talking generally before, I would not be looking to randomly create low spots with a hammer to then have to fill them.  It's hard without seeing what your doing, it sounds like you are using the guide coat to identify low spots, as you're saying the panel is still wavy. I don't see how you're not ending up with patches of guide coat remaining in a wavy panel? Once the high spots are knocked down to the correct level, surely to have a wavy panel you need low spots. And those low spots would have guide coat still in them?
    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      So I'll put filler past the repair area a bit to make sure I don't miss anything. Then I'll block it until it's almost level, put the guidecoat, then keep blocking until it's gone. Then it's still wavy.  In regards to hitting the panel, I saw this video might give more context - Skip to 0:47 he knocks it down. But yeah I'm sanding until the guidecoat is gone then checking because otherwise my filler is still well above the bodyline. Unless what you're saying is I should put guidecoat around it early, surrounding the filler then stip once it's gone?
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      I refreshed the OEM injectors with the kit and connected it up. It now ideals okay even with the IACV removed. Driving still has the same cutoff issue like the 550cc injectors so the issue is somewhere else. I bought FPG's Fuel Pump Hanger. I will be installing it next, but it is not as straightforward as I thought it was with my limited wiring knowledge and no instruction on the specific model I purchased (FPG-089). I also got the incorrect billet clamp as I could not find info on the OEM sizing.
×
×
  • Create New...