Jump to content
SAU Community

Recommended Posts

Skyline went to the mechanics 4 months ago. Prior to this the car had been off the road for about a year and a half. Got the car back from the mechanics after a major service (timing belt, bearings, water pump, head gasket, rocker cover gasket and the battery were replaced) and started having a similar issue with the engine surging at low rpm/rough roads.

Resoldered the AFM contacts which solved the problem up until 3 weeks ago when the same kind of issue returned. Took it back to the mechanic and he advised no AFM error codes were showing and it may be the fuel pump on its way out.

Last Sunday I replaced the fuel pump with a Walbro intank pump (GSS 341) and it stopped the surging for a day. This morning it came back. I am really at a loss at what is causing the issue but I am starting to think its electrical.

I am going to check the coilpacks for cracks and the wiring loom going under the right-hand side wheel arch this weekend. Until then - can anyone possibly think of some other areas to check that I am missing?

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/329605-r33-surging/
Share on other sites

Can you define "surging" in detail? in terms of your car's behavior when this happens.

Revs range from 500rpm > 2000rpm. If I keep my foot stationary on the accelerator the revs jump up and down quite quickly - the car sometimes accelerates when it happens. You can hear the engine note increasing/decreasing and the turbo sounds like its still spooling. The issue only seems to rectify itself after I pull over and restart the engine.

I've tried to accelerate out of it but the issue either continues or the engine stalls. No mods apart from an Apexi pod filter and the Walbro pump. Engine is idling at 600rpm is this normal?

Link to comment
https://www.sau.com.au/forums/topic/329605-r33-surging/#findComment-5355650
Share on other sites

Check;

ECU for fault codes (Potential CAS issue)

Coil packs for cracks (Could just duck tape them to test initially)

Spark plug condition & gap

Failing that put a FP gauge onto the rail and check what your getting against factory values.

If the AFM was bad previously, it may have fouled the plugs due to running in safe mode.

Edited by James_03
Link to comment
https://www.sau.com.au/forums/topic/329605-r33-surging/#findComment-5355661
Share on other sites

Check;

ECU for fault codes (Potential CAS issue)

Coil packs for cracks (Could just duck tape them to test initially)

Spark plug condition & gap

Failing that put a FP gauge onto the rail and check what your getting against factory values.

If the AFM was bad previously, it may have fouled the plugs due to running in safe mode.

Just bought a Consult cable so should be able to check for ECU fault codes alot easier on the weekend.

I was going to tape the coil packs after inspection as well. As for plugs NGK bcp6res should do the trick yes?

Link to comment
https://www.sau.com.au/forums/topic/329605-r33-surging/#findComment-5355978
Share on other sites

Just bought a Consult cable so should be able to check for ECU fault codes alot easier on the weekend.

I was going to tape the coil packs after inspection as well. As for plugs NGK bcp6res should do the trick yes?

yep, gap them to .8mm and youll be all good

Link to comment
https://www.sau.com.au/forums/topic/329605-r33-surging/#findComment-5355996
Share on other sites

aftermarket pumps arent supposed to work properly without a simple modification to the fuel pump wiring, i know the r32s had this from factory and i assume r33 would be the same. when engine is under load the fuel pump receives 12v but under low load conditions (idle, low throttle conditions etc) the pump will only receive 6v as full pressure isnt needed. the stock pump is designed to handle 6v obviously. aftermarket pumps usually aren't, and when u run this system through them they do all sorts of wierd things. i found this out when i upgraded mine to a walbro pump and it did not like this at all. it would start and idle fine, but the moment u give it some gas it would cough and splutter and miss all over the place. it was driveable, but trying to accelerate was a painful procedure.

the workshop who fixed it for me showed me a little grey box that they removed to fix it, located near the turbo. this little box is what switches the output voltage to the fuel pump. from memory they essentially just joined the 2 wires that went into it and the fix was as simple as that. from then on it received a consistent 12v, problem solved.

Link to comment
https://www.sau.com.au/forums/topic/329605-r33-surging/#findComment-5356007
Share on other sites

Revs range from 500rpm > 2000rpm. If I keep my foot stationary on the accelerator the revs jump up and down quite quickly - the car sometimes accelerates when it happens. You can hear the engine note increasing/decreasing and the turbo sounds like its still spooling. The issue only seems to rectify itself after I pull over and restart the engine.

I've tried to accelerate out of it but the issue either continues or the engine stalls. No mods apart from an Apexi pod filter and the Walbro pump. Engine is idling at 600rpm is this normal?

This sounds like a throttle position sensor or AFM issue. But more towards throttle position sensor.

Or unless if you have a really really dirty fuel tank. Which dirt clogs up the pump or fuel filter casing inconsistent fuel pressure. You fuel pump would sound very loud when that happens.

Link to comment
https://www.sau.com.au/forums/topic/329605-r33-surging/#findComment-5356043
Share on other sites

This sounds like a throttle position sensor or AFM issue. But more towards throttle position sensor.

Or unless if you have a really really dirty fuel tank. Which dirt clogs up the pump or fuel filter casing inconsistent fuel pressure. You fuel pump would sound very loud when that happens.

Mechanic did say that because the car sat idle for 1-2 years that a whole lot of sticky residue looked like it was in the fuel tank (he replaced the fuel filter that same visit). I replaced the stock pump with the Walbro to see if the residue had gummed up the pump. But alas - No change. I suppose that the only way to clean the tank is to drop it from the car?

Edited by Logikal
Link to comment
https://www.sau.com.au/forums/topic/329605-r33-surging/#findComment-5356092
Share on other sites

Wife just took the car for a quick test drive (long time car enthusiast) and said that she was getting the same issue going up a hill so she turned on "Snow" on the A/T and it seemed to reduce the severity of the surging. It also misfired whilst she was reversing slowly.

Problems seem to be getting worse :)

Link to comment
https://www.sau.com.au/forums/topic/329605-r33-surging/#findComment-5356167
Share on other sites

Well hooked up the CONSULT cable and ran ECUTalk and a couple of other programs.

O2 Sensor voltage seemed to be jumping about between 0.00 to 1.00 - Is this normal? When I turned the car over (Has not been turned on since Wed last week) it ran rough as guts and a strong exhaust fuel smell was present. Is there any parameter I need to watch specifically or would a log of my car running from ECUTalk be enough?

Edited by Logikal
Link to comment
https://www.sau.com.au/forums/topic/329605-r33-surging/#findComment-5363545
Share on other sites

Ok - Well that's good. As I an a complete novice when it comes to tuning, when changing the fuel pump is it advisable to change plugs / re-tune the ecu? The exhaust Also seems to smell of unburnt petrol. Is it running rich perhaps?

Link to comment
https://www.sau.com.au/forums/topic/329605-r33-surging/#findComment-5364684
Share on other sites

  • 4 weeks later...

I am going to clean the AAC valve tonight - will report on that tomorrow.

When I took the spark plugs out, I matched them to a thread on spark plug condition here and they ended up in the rich fuel/faulty ignition system category (hence why I taped the coil packs to see if that helped). One of the old plugs also emitted a noticeably stronger oil/fuel smell compared to the others.

I don't know if this is valuable info - but after the changing the plugs, reconnecting battery - I took it for a drive. Car started up and idled better than before. Took it for a test drive (30-40mins in both 60km/h and 100km/h zones) no issues and revs were stable. Took it for a drive last night - seemed to run a tad more rough than the test drive before but still had stable revs. Which brings us to this morning when the engine started to drop off and come back by itself nigh 5mins after driving the car.

It just seems every time I disconnect the battery/drain ECU it comes back nice for a short time then goes to the crappers again. I guess in the interim I will schedule a fuel system check/clean with someone. Any recommendations for workshops on the Sunshine Coast?

Link to comment
https://www.sau.com.au/forums/topic/329605-r33-surging/#findComment-5411581
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Lol yeah I ordered the clips mentioned and as far as the amayama diagrams go i think thats all I'll need. Fogured id ask, sometimes people's first hand experience doesnt always match up to diagrams haha, i guess I'll wing it and worse comes to worse I'll just deal with it as I go
    • Thanks for all that information I appreciate it. To answer your questions: - Yep that's what I mean. These guys are professional painters to so I must be missing something. It's a bit hard to explain. - With the primer landing on clearcoat, I make sure that the surrounding clearcoat is scuffed to 240 grit as my epoxy primer says that I only need to sand the area to 240 grit. - Yeah so similar to the first question, assuming that the paint landed on the unscuffed clearcoat because I've seen that happen. - Yep I want to prep the surface in that order. Only reason because epoxy primer will protect it from rust and I need that atm with this crappy Sydney weather. I think I was worried about time, if I try to put the filler down but screw it up somehow and I don't have time to sand it off and reapply it then need to put primer later that it might start to rust again so I wanted to apply the primer as quick as possible to not deal with rust.  - I just deleted some answers, I just realised after watching a video and what you said about looking at the data sheet, that I need to read the data sheet on the specific filler I'm using. It's possible now that I put epoxy primer first was a waste of time and need to go to bare metal lol
    • I did. I went to a suspension guy and he told me because I don't have adjustable camber arms it's the reason why my car veers towards the left if I take my hands off the wheel but if I drive my other every day car and take my hands off the steering wheel it goes completely straight. I think it's common with Skyline's. In order to fix the problem, I likely need gktech camber arms then nismo bushes since I have poly bushes atm, then a wheel alignment after that. With my car if I take my hands off the steering wheel on a really bumpy road before stopping at a light I have to hold my steering wheel somewhat tight otherwise my car will legit just go completely in the other direction quite quickly and I'll slam into something lol instead of stopping straight. I Believe this YouTuber had the same issue and fixed it with gktech arms. At timestmap 6:05 he talks about how the car doesn't veer anymore after installing these arms.  
    • hello! does anyone have a schematic that shows how to test the blower motor resistor for the vac system? i believe the part# is 27761-15U00. I think the resistor is toast, but would like to be able to test it somehow before i embark on the journey to find a new one. cheers! 27761-15U00
    • I don't know the answer to this, but did you have a look at the parts diagrams on amayama.com and see what they list around it for your car? As an example this should be it on my car. That's how I would check for required clips and things like that. But, I take no responsibility for you ending up with a box full of random OEM hoses, washers and clips after going down that path a few times. This definitely has never happened to me  
×
×
  • Create New...