Jump to content
SAU Community

Recommended Posts

1989 model R32 GTR In Gunmetal Grey

14,000 Km's On 320km Aftermarket Dash

Nismo Gear Knob

HKS adjustable Coilovers

Garrett GT2860-5 twin turbos

Full titanium catback exhaust (extremely light)

HKS Cam Gears

M's air PODS

HKS Hard Pipe Kit

No major accidents.

Price is $13,200. Car will be sold with stock wheels. CE28N's will NOT be included. Please send PM'S or call on 0421 128 922.

This price is ONLY valid if car is picked up by 27/07/2010.

http://www.carsales.com.au/all-cars/privat...500&trecs=1

Would anyone be interested if i took out the turbo's and made it cheaper again?

I need the car gone.

mate wish you were in sa id snap it up tomorrow.

Would anyone be interested if i took out the turbo's and made it cheaper again?

I need the car gone.

You would probably have more luck if you posted up more info about it such as rego, reason for selling, what stare your in and post the pictures up. Its a nice looking car but there's not much info there and its a very low price needing an urgent sale, which would raise suspicion.

If my car was sold i'd probably come check it out, so i know how you feel. Goodluck with the sale :(

How about an indication or estimate on the *real* odometer reading?

The ad is deceptive in that you state 14,000 and in the text at the bottom you repeat it and mention that is on the 320km/h aftermarket dash.

What reading was on the original dash when it was removed?

OK rego is due on 28/07/10 hence the huge price drop. Furthermore, I bought a new car a very long time ago. If you look up some of my other posts you will see a heap of parts for sale. I was epa'd a few weeks ago and only just cleared it a few days ago. With the car back to standard it just does not do it for me anymore. It's just not the same anymore. Furthermore, I have just bought an apartment so the money really will come in handy.

Engine is still running very nicely. Not a hand grenade at all. I welcome any inspection. I have absolutely nothing to hide. Cheap price because I want it gone.

Rough estimate of real km's on the car is 110 000. Timing belt has done less than 10 000km's. It has a gates timing belt in it now. Sorry I had no intention of being deceptive. I just assumed if anyone saw 320km dash they would know its been changed.

As I said next step would be to return the car to stock turbo's and remove coilovers too. Once I pay rego the price will go up again. Furthermore, do not assume I will drop to this price after I pay rego because I will not. I will request for this post to be removed after the 27/07.

If anyone has any questions please feel free to contact me. It is a genuine sale. Located in Glen Waverley, Melbourne.

Edited by chan
Rough estimate of real km's on the car is 110 000. Timing belt has done less than 10 000km's. It has a gates timing belt in it now. Sorry I had no intention of being deceptive. I just assumed if anyone saw 320km dash they would know its been changed.

Thank you for confirming the total km's in the thread, yes a person with knowledge would understand that the new dash would mean km's start at zero but it's still only fair to provide the estimate of the total km's the vehicle has travelled. Just providing the km's it has done since the new dash went in is not really helpful.

So it's safe to assume the 100,000km service has been performed?

Good luck with the sale!

Thank you for confirming the total km's in the thread, yes a person with knowledge would understand that the new dash would mean km's start at zero but it's still only fair to provide the estimate of the total km's the vehicle has travelled. Just providing the km's it has done since the new dash went in is not really helpful.

So it's safe to assume the 100,000km service has been performed?

Good luck with the sale!

Definitely done.

Thanks.

GTR SOLD AND GONE.

Congrats to the new owner. I have to say it was an absolute bargain.

Only two people came to have a look at it. First person was going to buy it. Second person did buy it.

Real shame it is gone and it will be missed.

Mods please close this thread.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...