Jump to content
SAU Community

Recommended Posts

1992 GTS-T - black - with green pearl

High Flowed T28 roller bearing turbo

Hks Cam wheels (inlet / exhaust)

Tein height adj coil overs

Pineapple bushes (two way- drag/drift)

Greedy boost gauge - with a pillar mount

17inch AVS wheels

Oil catch can

GTR strut brace

Kakimoto cat back system

Link piggy back ecu

HKS turbo timer

Blitz BOV

Blitz Air filter

HKS boost controller

Bomex front bar

AVO 103mm GTR intercooler

Recaro bucket seats x2

Tomei Fuel pump

Cusco lock differential (standard diff available)

Very clean car, engine in perfect condition, interior very neat (retrim)

$18,500AUD negotiable

1st to see will buy

Melbourne buyers preferably - 0412414173 or PM me

Link to comment
https://www.sau.com.au/forums/topic/33114-r32-gts-t-fs-high-mods-cheap-melb/
Share on other sites

motor is genuine, never rebuilt or removed. as for power figures, it produced around 185kw @ wheels on my dyno at BMT. Thats conservative considering the it was run at 1.0 bar only.

hmmmm nah i doubt u'll wanna swap... sam knows about my 32 its pretty average, u might have seen me down there a few times, my gf has a green soarer which was over heating and my GTST is black with GTR guards and bar.

good luck with the sale... altho if its still available in a month i'd be very interested.

Nope, this is good friend of mines car. Its never been at my shop if thats what you are asking. Its one of the original BMT cars that started with us years back.

Is there any chance you could READ the rules before posting. Posting for a friend is a NO-NO. Please get him to sign up and do his own posting so buyers can talk to him direct.

Thread has been locked.

Neil.

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...