Jump to content
SAU Community

Recommended Posts

No Wakkie this weekend :(.

Just a cruise meet n greet between NSW and ACT.

http://www.skylinesaustralia.com/forums/topic/418972-mid-march-mid-way-meet-up/page-3#entry6772390

Think there is a thread in NSW section - luke's the Orgyniser

  • 1 year later...
  • 6 months later...

So I was researching this issue and came across this thread. Looks like I have the same issue. On cold starts the 4WD system always works fine but sometimes on hot starts the 4WD error light comes up on the dash and the car is in permanent 2WD mode.

Had a look and it always seems to be error code 18.

Joey did you ever solve your problem mate? It's just painful with no 4WD the car is way to tail happy. I'll start testing this weekend hopefully but any insight would be appreciated.

  • 1 month later...

Just wondering if you guys resolved this problem?

I have an R32 GTR with error code 18. Tested the circuit as per the workshop manual and it's all good. However 4WD light stays on permanently and attessa pump only primes rarely on startup.

Any input from other people's experiences would be appreciated before I begin to change pressure switches and pumps out of desperation!

Look at the positive terminal on the battery. See if you can replace/improve the links.

Ravi - if you are replying to my comments I have a new battery and new cabling, solid connection. An auto elec also tested the entire Attessa circuit and all powers up fine.

Summary of my issue:

- 4WD and ABS lights stay on constantly

- Attessa computer reporting Error code 18: “ETS pressure switch or circuit fault”

- Auto elec checked all circuits and wiring thoroughly, all is ok

- 4WD pump primes on initial startup but no pressure going through lines to gearbox

- When pump is forced to prime (sending power direct to pressure switch) no fluid is coming to gearbox

Might have to bite the bullet and replace the pump!

Tried replacing the nitrogen canister above the rear diff ? It's 25 yrs old.

And I should add not cheap at around $400

That and then a flush of the fluid to be thorough

Made me a happy camper. :)

Tried replacing the nitrogen canister above the rear diff ? It's 25 yrs old.

And I should add not cheap at around $400

That and then a flush of the fluid to be thorough

Made me a happy camper. :)

Haven't tried, but makes complete sense to do so. Any advice on where I can get a new nitrogen canister?

Thanks for the response!

I didn't have any errors, but i replaced my canister and it totally changed the behaviour of the system during bleeding.

I got mine from rhdjapan (few months ago) it was about $280. My pump was starting to make funny noises from running all the time, wish I had changed it ages ago

  • Like 1
  • 6 months later...

So I was researching this issue and came across this thread. Looks like I have the same issue. On cold starts the 4WD system always works fine but sometimes on hot starts the 4WD error light comes up on the dash and the car is in permanent 2WD mode.

Had a look and it always seems to be error code 18.

Joey did you ever solve your problem mate? It's just painful with no 4WD the car is way to tail happy. I'll start testing this weekend hopefully but any insight would be appreciated.

Very late reply, I did end up solving the issue mate, what the issue actually was, stuffed if I can remember haha think it may have been battery related

I've actually got another fault now so will be interesting to see what that one is as well

Did this fix it mate?

Yes my 4WD is working like a dream now. Fitted the new nitrogen canister and bought a digital G-sensor to replace the old original sensor... Car hooks up all four wheels almost instantly on the track! No tail happy over steering with delayed torque split anymore.

Next I will rebuild the transfer case to ensure best possible mechanical engagement.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • @Murray_Calavera  If I were an expert I wouldn't be in here looking for assistance.  I am extremely computer literate, have above average understanding on how things should be working and how they should tie together.  If I need to go to a professional tuner so be it, but I'd much rather learn and do things myself even if it means looking for some guidance along the way and blowing up a few engines. @GTSBoy  I was hoping it would be as simple as a large vacuum leak somewhere but I'm unable to find anything, all lines seem to be well capped or going where they need to be, and when removed there is vacuum felt on the tube.  It would be odd for the Haltech built in MAP to be faulty, the GTT tune I imported had it enabled from the start, I incorrectly assumed it was reading a signal from the stock MAP, but that doesn't exist.  After running a vacuum hose to the ECU the signal doesn't change more than 0.2 in either direction.   I'll probably upload a video of my settings tomorrow, as it stands I'm able to daily drive, but getting stuttering when giving it gas from idle, so pulling away from lights is a slow process of revving it up and feathering the clutch until its moving, then it will accelerate fine.  It sounds like I need to get to the bottom of the manifold pressure issue, but the ignition timing section is most intimidating to me and will probably let a pro do that part.  Tomorrow I'll try a different vacuum line to T off of, with any luck I selected one that was already bypassed during the DBW swap. @feartherb26  I do have +T in the works but wanted to wait until Spring to start with that swap since this is my good winter AWD vehicle.  When removing the butterfly, did it leave a bunch of holes in the manifold that you needed to plug?  I thought about removing it but assumed it would be a mess.   I notice no difference when capping the vacuum line to it or letting it do its thing.  This whole thing has convinced me to just get a forward facing manifold when the time comes though.
    • Update: tested my spark plugs that are supposed to be 5ohms with a 10% deviation and one gave me a 0 ohms reading and the rest were 3.9ohm<, so one bad and the others on their way out.
    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
×
×
  • Create New...