Jump to content
SAU Community

Looking For Lower Seat Than Gt-r Seat

On Edge

By On Edge,
in Motorsport Discussion & Builds

 Share

Recommended Posts

On Edge Veteran

On Edge

Posted
Posted

hey people,

i currently have nismo 400r seats in my r33 an would like to buy a fixed bucket seat for holding, as well as having a lower seating position.

my question is do most fixed back seats sit lower than the GT-R one? An if so by how much

Any help would be much appreciated

phunky_monkey Grand Master

phunky_monkey

Posted
Posted

The lower seating position is usually achieved by the rail rather than the actual seat itself. If you want to go low and don't want to go custom, I'd suggest a Bride Super Low rail teamed up with whichever seat you like (and that fits).

On Edge Veteran

On Edge

Posted
  • Author
Posted
The lower seating position is usually achieved by the rail rather than the actual seat itself. If you want to go low and don't want to go custom, I'd suggest a Bride Super Low rail teamed up with whichever seat you like (and that fits).

thanks for the reply

yes low rails will definately help, an i think that the GT-R seat is a lil chunky underneath.

Im looking at getting the sparco evo 2 plus with low rail, hope it sits lower

Can anyone confirm?

FineLine Grand Master

FineLine

Posted
Posted
thanks for the reply

yes low rails will definately help, an i think that the GT-R seat is a lil chunky underneath.

Im looking at getting the sparco evo 2 plus with low rail, hope it sits lower

Can anyone confirm?

Thats the exact combo i am using and yes it is lower than the 33 gtr seat. I have the gtr seat as a passenger seat and there is a noticeable difference in seat height.

  • Nope 1
phunky_monkey Grand Master

phunky_monkey

Posted
Posted
thanks for the reply

yes low rails will definately help, an i think that the GT-R seat is a lil chunky underneath.

Im looking at getting the sparco evo 2 plus with low rail, hope it sits lower

Can anyone confirm?

What rail is it?

Yes the seat is chunky, but I'm telling you that 90% of the height difference will be in the choice of rail.

Beer Baron Grand Master

Beer Baron

Posted
Posted

yep, rail design is the key. sometimes you will need a base plate to provide a flat surface, then bolt sliders to that so seat can move back and forward and then you bolt your side mounts to the sliders and the seat to the mounts. with all that stuff you end up with a fair bit of height. removing the sliders gives back about 20mm or so maybe even 30mm depending on design. you do still need some kind of base plate though to give a level mounting surface for the side mounts. the other option is modify the floor to allow you get a flat frame for the seat nice and low. lot of work though and must be done professionally.

phunky_monkey Grand Master

phunky_monkey

Posted
Posted
the other option is modify the floor to allow you get a flat frame for the seat nice and low. lot of work though and must be done professionally.

I had this done in the 180, and although it was pricey my shoulder now lines up with the door frame and I'm 6'4. Super low!

Having said that, a good Bride super low rail will drop you significantly for around $300. The drop depends on the car; in the 180 it was great until I got the cage which obstructed my seating position. In the STi I sit even lower than the 180 with the modified floor (feels that way anyway). Ridiculously low at it's lowest setting, but three heights to choose from.

Buddhz Apprentice

Buddhz

Posted
Posted

So which bride rail did you have before you modified your floorpan Dane?

Was it low enough for you to wear a helmet without the cage?

I have a bride rail with an older model Profi SPG in my S13 atm (its not the lowest one) and with a helmet my head hits the roof. I'm only 6' as well which is strange - maybe my body is out of proportion :(

phunky_monkey Grand Master

phunky_monkey

Posted
Posted

It may be mate! :(

I think it was an FO, and I fit with just enough room though I'm 4 inches taller than you. That's with an SPA so much of a muchness.

In the STi I have an FG and it is super low, so I'd actually suggest trying one of those out.

FineLine Grand Master

FineLine

Posted
Posted
So which bride rail did you have before you modified your floorpan Dane?

Was it low enough for you to wear a helmet without the cage?

I have a bride rail with an older model Profi SPG in my S13 atm (its not the lowest one) and with a helmet my head hits the roof. I'm only 6' as well which is strange - maybe my body is out of proportion :(

mate just go to revolution race gear and get the generic seat rail they sell for the sparco evo 2. I'm 6'1 and I have no damn probs with a helmet and a roll cage.

  • Nope 1
On Edge Veteran

On Edge

Posted
  • Author
Posted
mate just go to revolution race gear and get the generic seat rail they sell for the sparco evo 2. I'm 6'1 and I have no damn probs with a helmet and a roll cage.

thats where im buying my seat an the rail im looking at using, did you have much trouble with installation?

FineLine Grand Master

FineLine

Posted
Posted
thats where im buying my seat an the rail im looking at using, did you have much trouble with installation?

None at all, when I got around to doing the cage I had to cut the rail that seperates both side rails so the seat could go down a slot or 2. Its pretty basic stuff mate.

  • Nope 1
phunky_monkey Grand Master

phunky_monkey

Posted
Posted
mate just go to revolution race gear and get the generic seat rail they sell for the sparco evo 2. I'm 6'1 and I have no damn probs with a helmet and a roll cage.

I have a generic type base rail with RPM side mounts in my passeneger seat, check the height difference out. That's without sliders too.

BUT I didn't cut the middle out to drop it, don;t think I can with the width of the SPG-N.

post-8405-1281065615_thumb.jpg

FineLine Grand Master

FineLine

Posted
Posted
omg thats great :( sorry to be a pain but how much do you reckon the driving height would have been lowered from a GT-R seat?

wish my car was here and not at the workshop so i could actually go measure.

From memory about 25/30 mil. You can also rake the seat back a bit to give yourself more head room by going to a lower slot on the back.

  • Nope 1
FineLine Grand Master

FineLine

Posted
Posted
I have a generic type base rail with RPM side mounts in my passeneger seat, check the height difference out. That's without sliders too.

BUT I didn't cut the middle out to drop it, don;t think I can with the width of the SPG-N.

I see what you mean phunk. That rail is a different animal to mine. Mine is actually a slider and is way lower than that puppy.

  • Nope 1
On Edge Veteran

On Edge

Posted
  • Author
Posted
wish my car was here and not at the workshop so i could actually go measure.

From memory about 25/30 mil. You can also rake the seat back a bit to give yourself more head room by going to a lower slot on the back.

yeah tru that, beautiful cant wait to get it, do you remember what the name of the rail was?

FineLine Grand Master

FineLine

Posted
Posted

Now that I cant help you with. what I can tell you to assist with I.d. is that it has a lever on either side of the rail with a brass knob on the end. these levers are lifted to the verticval position to slide the rail and back to the horizontal to lock it in place.

  • Nope 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The king 2.0
      Nissan fuga 450gt android screen

      By The king 2.0 · Posted

      Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • MBS206
      NC MX5

      By MBS206 · Posted

      My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • dbm7
      Automatic Power Button Light Flashing

      By dbm7 · Posted

      Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Duncan
      R34 Plug Identification

      By Duncan · Posted

      Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...