Jump to content
SAU Community

R32/3 Quality 2.5" Fmic Piping Kit,r32 Rear Coilovers

Drift Engage House
 Share

Recommended Posts

Drift Engage House Enthusiast

Drift Engage House

Posted
Posted

r32/3 RB20/5DET front mount intercooler piping and silicones everything needed for the job exept cooler itself,consists of everything pictured,all calibre and HDI silicones so not cheap crappy ones,reducers are 3" to 2.5" to fit 3" inlet and outlet coolers.other kits only come with 3 pipes and you end up still needing another piece on the hot side to join,this comes with 5 to make things easyer.

$200ONO all offers considered.

post-60301-1280919097_thumb.jpg

R32 GTST REAR GAB coilovers - good nick,used them for about 4-5 month's got a new full set so not needed anymore - $170ono

post-60301-1280919250_thumb.jpg

RB20DET factory coilpacks - $80

RB20DET factory injectors - $50 set of 6 (have 3 sets)

r32 stock exhaust - $50

RB20DET altinator - $40

RB25DET altinator - $40

RB20DET factory parts - have 3 complete RB20DET's im stripping down (2x silvertops 1x redtop) all parts avaliable (redtop cams SOLD)

greddy turbo timer - new style,transperant blue - $60

S13 taillights - pair,factory mint condition - $40 (stripping the whole S13,engine,loom,front seats,gearbox SOLD)

all parts in perfect working order unless stated.

make an offer on anything im easy going.pick up S.E burbs melbourne or post at your expense.can deliver for a small fee also.

PM,email ([email protected]) or sms on 0402605401

thanks very much

James

seriesII Mentor

seriesII

Posted
Posted (edited)

hi, ill take the piping kit... i can setup a courier to pick it up?..

$130 plus postage yeah?. thanx

Edited by seriesII
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Komdotkom
      R32 Gtst - Track Car

      By Komdotkom · Posted

      Good luck on the weekend mate
    • Duncan
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Duncan · Posted

      Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Duncan
      New

      By Duncan · Posted

      Welcome to SAU, what are you looking at buying?
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...