Jump to content
SAU Community

Motec M800 /trust Greddy T517zs Reco'ed Fs

Gtir-keiron
 Share

Recommended Posts

Gtir-keiron Community Regular

Gtir-keiron

Posted
Posted (edited)

Motec M800 wideband lamba enable and datalogging

Full Loom with all the sensors

The custom loom has been marked for easy install (set up for rb25/26)

Bosch Super sports 491 leads

Bosch coils

CDI AEM Ignition module

Basicaly this stuff is all new or seen very little use,I picked it up for a project car that i have since sold as of today.

The motec has been tested and is unlocked in perfect working order.

I will fully refund any ones money if there is any problems at all with this gear.

To buy all of this stuff and have the added extras opened on the motec will cost you over 6g

Every thing is in perfect working order and is as new so grab your self a bargin.

My motec installer told me i did not need to buy a single thing every thing is here and ready to install.

I would post pictures but my phone wont connect to the pc,If any one wants pictures of the gear im more then willing to send them via text

Price $3850 ono

Trust Greddy T517z's

Serial number 021008012

Direct bolt on replacement for your gtr skyline.

I picked these up for a project that was sold today,One turbo was damaged so i simply had new cores/cartidges put in both turbos

Again these turbos are bascialy new and have had no use at all since rebuild.

Comes with acuators drains and so on,Also ill throw in the old cartridges and spare parts,There would be enuff parts to rebuild one turbo if you ever needed to.

These turbos retail new for around 4 grand

Price $2850 ono

Edited by Gtir-keiron
Gtir-keiron Community Regular

Gtir-keiron

Posted
  • Author
Posted
What size rear on the T517Z's? Also, what were the new cartridges, from Greddy/Trust or MHI equivalent?

Mike

the cartridges came from jpn mate.

I just paided a performance mechanic to put them together.

Ill have to check the rear on the t571zs is there any kind of marking i should be looking for mate?

Gtir-keiron Community Regular

Gtir-keiron

Posted
  • Author
Posted
They will have a 8cm or 10cm exhaust housing; should be on the casting. Can you post some pics?

They are 8cm rear housing mate approx 360 hp worth around the same 25/30 hks turbo

Gtir-keiron Community Regular

Gtir-keiron

Posted
  • Author
Posted (edited)

pms replied.

Please stop the lowballing on the motec guys every one knows what its worth to buy and have all that stuff upgraded.

Even in the 2 upgrades alone with the motec unit and just the upgrades your out of pocket over 4g.

If your really keen on the best computer on the market for your car with all the extras shoot me a text or give me a call on

0427284275

Edited by Gtir-keiron
Gtir-keiron Community Regular

Gtir-keiron

Posted
  • Author
Posted
Is the aem a 4 channel or 8 channel, and would you consider seperating?

I don t really want to mate if i can help it.

Id rather sell the package complete.

Gtir-keiron Community Regular

Gtir-keiron

Posted
  • Author
Posted

Enable M800

Hi/lo injection

Lamba Single

Logging 1M

Servo control

LSU4.0 (6066) Lambda sensor3 bar MAP sensor2 x 63CP0220 - 250AUNAOC TI or Honeywell sensors (oil and fuel pressure) approx $200 eaDelco Air Temp sensor (Brass)Bosch Engine Temp SensorMotec Mx00 series wiring loom6 x Bosch supersport ignition leads AEM 2801 4ch CDI6 x Bosch EL faclon coils (with bosch LJET 2 pin plug connection)

My motec dealer just price listed every thing up and the grand total is just over $6500.00

So grab your self a bargin at near half the price for as new items.

Gtir-keiron Community Regular

Gtir-keiron

Posted
  • Author
Posted

Enable M800

Hi/lo injection

Lamba Single

Logging 1M

Servo control

LSU4.0 (6066) Lambda sensor

3 bar MAP sensor

2 x 63CP0220 - 250AUNAOC TI or Honeywell sensors (oil and fuel pressure) approx $200 ea

Delco Air Temp sensor (Brass)

Bosch Engine Temp Sensor

Motec Mx00 series wiring loom

6 x Bosch supersport ignition leads .

AEM 2801 4ch CDI6 x Bosch EL faclon coils (with bosch LJET 2 pin plug connection)

My motec dealer just price listed every thing up and the grand total is just over $6500.00

So grab your self a bargin at near half the price for as new items.

bump

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      Kittens in first to claim dominance of the residence, then puppies later From past experience, the other way around can be problematic to say the least  Those weird "Dobby looking"  little kittens are not cheap....LOL
    • MBS206
      NC MX5

      By MBS206 · Posted

      At least yours have parkour down pat. One of mine will still trip over his own shadow and fall over... He's a special type of cat... Ha ha ha
    • MBS206
      NC MX5

      By MBS206 · Posted

    • SteveL
      Leak from Tokico BM50 Brake Master Cylinder

      By SteveL · Posted

      The question then becomes - was there any fluid coming from that hole before you did the rebuild ?    You may not have noticed, of course.   Depending on how you did the rebuild, the possibility has to be considered that somehow (cleaning ?)  fluid entered that hole and is now being 'forced'  out by small movements of the proportioning valve.   From the factory, there's actually a small rubber plug in that hole but with age and under-bonnet heat it's quite common for it to 'go missing'.  That rubber plug is designed to allow the venting process but also to prevent 'stuff' getting to the area (prevent corrosion, etc).   The plug is also not available as a spare part AFAIA. Personally I wouldn't race and buy a new master just yet but keep an eye on the area to see if the 'leak' continues.   If you're concerned about brake fluid damaging nearby paintwork, cable tie a piece of suitable absorbant material over the hole and remove/monitor occasionally.    Operation of the proportioning valve and the brake master itself won't be affected, but also keep an eye on brake fluid level, of course. In terms of a new master, the genuine part is getting expensive, unfortunately.  Amayama is showing AUD900+.   I was searching recently and there's an aftermarket part available from Japan made by 'Parts Assist': https://zenmarket.jp/en/yahoo.aspx?q=BNR32%2bBM50&p=1 Whether it's any good I have no idea, although in my experience Japanese aftermarket stuff is pretty good quality-wise.   The above site allows overseas buyers to purchase stuff more easily from Japan but there are fees and shipping costs, of course.   The original Japanese seller page is here: https://auctions.yahoo.co.jp/jp/auction/p1197401228 Copper/Nickel is fine but I still prefer bundy tube and it's also cheaper.
    • Duncan
      NC MX5

      By Duncan · Posted

      Your chihuahuas look weird!
×
×
  • Create New...