Jump to content
SAU Community

Recommended Posts

Sup,

I've finally gotten around to finishing a ton of work, including my new -5's. But it's now a bitter sweet situation.

I started it up, not a problem, engine started first crank as though I drove it yesterday. Idled like a dream, not one issue, I was happy.

Then it developed a very minor misfire on idle. It had been idling for about 15 minutes by this stage, letting everything warm up to check for any leaks, etc. I kinda figured the fuel was crap by this stage, but still good enough to drive it away, since the misfire was minor. Big mistake which will cost the money I saved on some bargains.

Took it out, up the street, light throttle about 3000rpm then it started dying instantly. It was like a switch, engine off, engine on, engine off, engine on, in half second intervals. Obviously I turned around asap and took it home, where after it died coming into the driveway.

Since this happened I've drained the 40 or so litres from the car, it was a very orange/red colour (assumption: dead fuel) and I'm not really versed in the smell, but it didn't smell 'potent' like good fuel does. I drained it by hotwiring the pump and running till empty. I then put 10 litres of VPower in it, pumped it through the rails, then drained all of that as well. Then I pumped a full tank of brand new VPower. Still wouldn't start though.

So then I replaced the fuel filter, the old one felt quite blocked when I blew through it. With the new one installed, tried again, still wont start properly. - It stutters with the starter motor on occasion, sometimes it'd start running and misfire for 2 secs, then dies again but it's been doing this since the problem started.

Pulled the plugs out, all 6 spark fine off all 6 coils, but I replaced them anyways with new BCPR7ES's. It still wouldn't start.

Took the plugs out, and they are wet with fuel. I crank the engine without the plugs and I can see fuel run over the top of the pistons, all of them.

----

So whats going on here? The fuel works, the spark works.

The engine DID run fine, and slowly degraded, so I put electrical problems behind me.

The spark plugs all sparked fine, on all coils, so I ruled out ignition.

New air filters, def not blocked.

If the injectors (Enterprise 700cc, traveled 3000km) were blocked, I'd get no fuel?

Should I see fuel vapor coming out of the engine? Or fuel running over the top of the piston? (By run, I mean very minor, I see wetness appear and fade, not a tidal wave)

Could it be a possibility the injectors are hosing the engine?

Anyone know a reputable fuel injector cleaner on the Coast? I know of them, but I haven't used anyone before.

Anyone had experiences with this exact problem? I know some GTR's don't get driven often at all.

Excuse the thoroughness, just explaining everything step by step in case anyone else has had the exact same thing happen and know exactly what was fixed.

Cheers in advance as always.

Link to comment
https://www.sau.com.au/forums/topic/332180-stale-fuel/
Share on other sites

what exactly did u do to the car? all you have said is new turbos, did you install bigger injectors too ? by the sounds of it you have over fueled the engine big time and possibly glazed the cylinders

Car runs a power fc, z32 afm's etc. The afm's and injectors were installed at croydons and tuned from there. That was over a year ago. None of that was changed, just new turbos and dumps on the engine. (Car hasn't been driven at WOT with new turbos either for obvious reasons until tuned)

And to add, the car was running perfectly fine, after 15 mins of idle it started to play up.

Edited by GTRPowa
Link to comment
https://www.sau.com.au/forums/topic/332180-stale-fuel/#findComment-5388520
Share on other sites

what exactly did u do to the car? all you have said is new turbos, did you install bigger injectors too ? by the sounds of it you have over fueled the engine big time and possibly glazed the cylinders

It takes frickin AAAAAAAAGES to glaze bores with extra fuel when an engine is already run in. It's only fresh engine that this is a problem for.

Check to make sure you plugged the AFM's in and check that you plugged them into the correct ones.

Go into sensor check and make sure you get a reading from them as well

Link to comment
https://www.sau.com.au/forums/topic/332180-stale-fuel/#findComment-5388564
Share on other sites

Your air flow rates should show up on your hand controller, the only thing that won't will be the boost (unless you have the apexi add-on). This is just for the RB26's, RB25's don't show an airflow rate :)

Don't know wether or not I missed it, and it's now a moot point but, how long was the fuel sitting around for?

So at the moment, the starter motor cranks, but it just won't fire over? The only thing that I can think of that's not checking all your plugs and other crap like that is maybe the injector timing or tune was lost at some point, but highly unlikely.

Link to comment
https://www.sau.com.au/forums/topic/332180-stale-fuel/#findComment-5388575
Share on other sites

Do a sensor check through the FC as already mentioned.

Sounds like it was running without AFM's and consequently fouled the spark plugs. I am actually suprised that it didn't kick after you replaced the plugs.

Pull the feed line off the rail too and check your getting good pressure with the ign on.

Link to comment
https://www.sau.com.au/forums/topic/332180-stale-fuel/#findComment-5388605
Share on other sites

agree

a key sensor is toast, loose, faulty or being silly

check ETC SENSOR SW CHECK

stale fuel would just make it detonate on full load (engine light going spazzo)

it wouldnt make it start / stop / start like you described

Link to comment
https://www.sau.com.au/forums/topic/332180-stale-fuel/#findComment-5388679
Share on other sites

agree

a key sensor is toast, loose, faulty or being silly

check ETC SENSOR SW CHECK

stale fuel would just make it detonate on full load (engine light going spazzo)

it wouldnt make it start / stop / start like you described

^^^^ +1

Have started cars after 2 years of sitting and fuel was not a problem, not ideal, but not your cause

Link to comment
https://www.sau.com.au/forums/topic/332180-stale-fuel/#findComment-5388777
Share on other sites

Yeah the AFM's are plugged in, and I assume they are correct because the connectors don't reach the opposite AFM's. I didnt think it mattered which AFM was plugged into where, because it averages the both?

I was looking at sensor check when the car was actually running, both AFM's, O2's, TPS, etc etc were working. The Idle as well.

I spoke with a fuel injection guy this morning and he thinks it could be the ignition/ignitor. I'm going to test the length of the arc with a screwdriver as we speak. He also said with all the fuel dyes nowadays that my red fuel could have been just that, red fuel.

I will also review my Sensor Check again.

Any further tips appreciated.

Link to comment
https://www.sau.com.au/forums/topic/332180-stale-fuel/#findComment-5388881
Share on other sites

WTRT is pretty high

what does MONITOR, 1 CHANNEL, WATER TEMP show ?

Both water and air temp show 14 degrees C, my current ambient temperature.

I was thinking that this problem is indicative of the CAS on the way out. I've taken it off and done some measurements as per the manual, but I'm getting vague readings from it.

Eg, I'm supposed to get 12 volts on terminal 3 with IGN on, I always get this without a problem.

However terminals 1 and 2 are supposed to alternate between 0 and 5v? I expect nothing in between?

On terminal 1 I get 0.02 volts, earlier it would change to 0.07 volts when a gap in the CAS disc would pass the sensor (This is inside the CAS). Now It's always 0.02v no matter the angle of the CAS.

On terminal 2 i get fluctuating voltages from 0 to 5 and anything in between. Shaking the CAS makes the volt meter go all over the place, I see voltages such as 0.40, 2.68, 3.7, 4+ etc.

On top of all of this, when I turn the sensor with the PFC on, I should see the engine rpm going up? When I crank the engine with the CAS installed I should also see the RPM going up? And again, when cranking I should see my tach needle go up a tad? None of this happens.

However once of twice when cranking I've seen the engine speed touch 180 for a moment, I've also seen it touch 4000 rpm or so, this is while cranking. But 99.8% of the time it stays on 0 rpm.

^ Btw I havent known this all along, just came to notice a question in the Service Manual saying "Does your tech needle move up while cranking?" - Made me think about the CAS on it's way out.

Suggestions? Cheers again.

Edit: The CAS itself spins smoothly, no clicking, friction, or problems. There was also no dust inside the CAS at all. Are they cleanable/servicable? I see more screws inside the CAS but I dont want to dig that deep yet.

Edited by GTRPowa
Link to comment
https://www.sau.com.au/forums/topic/332180-stale-fuel/#findComment-5389143
Share on other sites

its a 32 gtr... they have plastic fuel tanks.

try this. disconnect injector main plug, take plugs out. crank engine over to clear out fuel, burn off spark plugs if they are dripping in fuel. put back together and then take hose off the intake plenumn (the cooler pipe hose) and crank the engine while someone sprays some aerostart into the plenumn. if the engine fires into life you defo have a fuel related problem. if no fire then its going to be something like ignitor, cas or AFM, but even then if you have spark it seems unlikely. as an engine will fire with no AFM plugged in.

Link to comment
https://www.sau.com.au/forums/topic/332180-stale-fuel/#findComment-5389508
Share on other sites

also to check the cas is working you can turn the ignition on and turn the cas over by hand. the injectors should click one at a time until all 6 have c licked. you can also test spark using this method also. if you have both the cas is fine.

Yes this is what I have done and I can't hear the injectors. I also had my FC controller with me and it was always sitting on 0 rpm, no matter how fast you turn the CAS.

I've borrowed an identical CAS from a friend, installing it tomorrow. I'll post my results when I get up. Night shifffftttt.

Link to comment
https://www.sau.com.au/forums/topic/332180-stale-fuel/#findComment-5390446
Share on other sites

I have seen quite a few people (including myself once upon a time) install the CAS back on the bracket with no front cover or spacers.

You either run the front cover, or you have to space the CAS out from the bracket, doing neither will wreck them quickly.

Won't be your issue if your running front cover/spacers but.

Link to comment
https://www.sau.com.au/forums/topic/332180-stale-fuel/#findComment-5390512
Share on other sites

Ok, turns out it was the CAS plug. I got a mates CAS, plugged it in, no difference. I then plugged mine back in, and it was working. Installed it into car, stopped working.

Used electrical contact cleaner, and slightly bent the CAS prongs so it makes a better connection. Took the car out for a good 1 hour drive, all is well.

Thanks again for helping to solve this annoying problem.

Link to comment
https://www.sau.com.au/forums/topic/332180-stale-fuel/#findComment-5391547
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The car/ECU will have all the sensor that it needs and expect to have. I think i do not have to explain to you how the Link is way better specialy if you have swapped engine   I just do not want to deal with any "problems" cuz i have only Nistune which i learned is not that great and in my case cant even deal with that speed problem (Link can) And of course it will be way more easier to tune and diagnose and safe. And for the ECU/speed problem...i dont know.
    • Per Mark Roberts of Sonictune: Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • Per Mark Roberts of Sonictune:     Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • The fancy pants red shock tower brace is finally incoming from MX5 Mania, getting it shipped from 'Merica has been a long and problematic process, and GWR, the 'Merican supplier will not ship directly to consumers outside of the US, Mania basically had to order a heap of them, the colour choice was silver, or red, and we all know anything red adds 5 killerwasps of dynotorques..... Whilst it does fit over a 2.5, and I've seen a few photos and videos of it being installed and fitting, google also says it might get real close to the FAB9 intake front runner, people in the US says it does fit with the FAB9 intake, except for one person who said it slightly touched.......so there is that.....LOL..... As it seems that I am the first in AU to have this combination of parts there's no local knowledge about fitment, so I'm just a willing guinea pig in this endeavour, I'll cross my fingers and toes and hope for the best In other news, I ordered stuff from China  on the same day I ordered the 23° silicone bend from Victoria, the stuff from China arrived a day ago, the 23° silicone bend is still travelling around Australia thanks to Australia Post, and "may" be here next week
    • Very good news...I contacted Racebox about it last night. My car is a 2016 so remains to be seen if it is compatible, requires a TCU swap, or is impossible.
×
×
  • Create New...