Jump to content
SAU Community

Recommended Posts

Hey everyone,

My name is James and in around 2 Months I get my P Plates. I live in Adelaide and Im looking for a car. I have a really big interest in Nissan Skylines, and with all my heart i really want a R32, but even a 33 would be nice.

So im here posting on this forum to do my homework about the car. I have a basic understanding of it and just want to know some other specs about them.

I dont have that much cash to play around with around $7500 i have, give or take a few hundred and thats around the highest mark i can go. With the new law coming into South Australia which is fu**ing bullshit i can not drive a turbo, so that has put me off this car abit, but im still really keen in getting one and im not sure if its worth getting one without a turbo then when im abit older i can put one in.

So im posting on these forums just wanting some of your help finding out

- the common problems

- Maintenance cost's and running cost's.

Im asking for your help i hope that you guys can help me out with this

Thankyou in advance

James :worship:

Link to comment
https://www.sau.com.au/forums/topic/332430-need-advice/
Share on other sites

if a turbo is what you want, then save your cash until you can have one. trust me, when you want a turbo, then a non-turbo will never satisfy. im speaking from experience.

in saying that though, it might not be such a good idea to stick a novice driver behind the wheel of a turbo. having the non turbo taught me a lot about the car's handling characteristics etc and by the time i got myself into a turbo i was already well experienced at handling that car.

as for common problems.. coils seem to be the most prone to failure, tend to cause far more problems on turbo's though.

maintenance and running costs.. too many variables there to say accurately. most skylines these days are all in various condition, with various modifications, maintained by technicians of widely varying caliber's.

my advice would be to buy one completely stock standard. my first skyline was stock standard and it was the most reliable car i've owned yet. my turbo was already modified and because you never know who's had their greasy paws in your engine bay its like opening a can of worms.

for the love of god, whatever you do, get a pre-purchase mechanical inspection done. never again will i buy a skyline without one.

Link to comment
https://www.sau.com.au/forums/topic/332430-need-advice/#findComment-5392091
Share on other sites

if a turbo is what you want, then save your cash until you can have one. trust me, when you want a turbo, then a non-turbo will never satisfy. im speaking from experience.

in saying that though, it might not be such a good idea to stick a novice driver behind the wheel of a turbo. having the non turbo taught me a lot about the car's handling characteristics etc and by the time i got myself into a turbo i was already well experienced at handling that car.

as for common problems.. coils seem to be the most prone to failure, tend to cause far more problems on turbo's though.

maintenance and running costs.. too many variables there to say accurately. most skylines these days are all in various condition, with various modifications, maintained by technicians of widely varying caliber's.

my advice would be to buy one completely stock standard. my first skyline was stock standard and it was the most reliable car i've owned yet. my turbo was already modified and because you never know who's had their greasy paws in your engine bay its like opening a can of worms.

for the love of god, whatever you do, get a pre-purchase mechanical inspection done. never again will i buy a skyline without one.

Thankyou so much mate, for your advice.

thats what im thinking, im thinking of buying a stock standard R32 then save some money then when i can afford to get a Turbo put it, im glad that someone has told me that, ive been thinking to do that but i wasnt sure if it was a stupid idea. Also talking about common problems, with coils how much are we talking because i have a limit on how much i can spend.

max is around $7500 also how much do you think i should put away for first year maintance??

thankyou man i appreciate this so much.

Link to comment
https://www.sau.com.au/forums/topic/332430-need-advice/#findComment-5392269
Share on other sites

http://www.skylinesaustralia.com/forums/bu...e-f-t35129.html

http://www.carsales.com.au/all-cars/privat...id=12918C227C36

Only NA on carsales under 10k in SA =/

Looks like decent value if there are P plate laws coming in. Needs a small bit of work... Learn on it :worship:

http://cgi.ebay.com.au/NISSAN-SKYLINE-R34-...=item255c75450b Vic tho.

http://cgi.ebay.com.au/R33-Skyline-GTS-/32...=item4aa38b8d9e NSW.

Edited by Ten Four
Link to comment
https://www.sau.com.au/forums/topic/332430-need-advice/#findComment-5392289
Share on other sites

i may get slammed for this but hey its just MY opinion. i believe you should just buy a turboed car straight up. think about it, say you buy a NA powered skyline then down the track you decide its time for a turbo, well your gunna be up for some solid dollars to convert the car to turbo. you need loom changes ecu changes find a turbo and manifold plus exhaust to suit. change the cams injectors etc etc. your looking at a few grand to achieve this reliably. SO whats involved in getting in trouble for driving a turbocharged vehicle should you ever get caught (dont go modifying straight away like front mount exhaust blah blah blah) id say for the small chance you will be found out its worth the risk. hey you might get a fine but its certainly not gunna be anywhere the amount to have the car up to the same specs as a originally turboed vehicle. this is just MY opinion so use this as advise only. these were my experiences and they r not necessarily the right thing to do but simply put a smart option. meh., :worship:

Link to comment
https://www.sau.com.au/forums/topic/332430-need-advice/#findComment-5392336
Share on other sites

yeah the p plate laws are coming in in less than a month, so he will have to get a non turbo.

my honest opinion would be to just get a commodore/falcon or v6 magna or SSS pulsar (unless you are one of the idiots who thinks fwd is shit because you can't do fully kebab style burnouts) for now and then get a turbo skyline when you are off your p's. all of the above will be as fast or faster than a natro skyline and be cheaper on parts, insurance, etc, and get you less attention from the police

Link to comment
https://www.sau.com.au/forums/topic/332430-need-advice/#findComment-5392885
Share on other sites

James, in all honesty, you're better off spending $2K on a manual R31 Skyline or KE70, and putting the rest in the bank till you're off your Ps. Learn your skills in a car that won't have you bleeding if you dent or scratch it.

Link to comment
https://www.sau.com.au/forums/topic/332430-need-advice/#findComment-5393942
Share on other sites

+2. get a cheap shitbox rwd for now, and save your cash hard until your off the Ps and you will be able to afford something epic. i wish someone gave me that advice when i was a nipper. actually someone probably did, but i doubt i was listening.

Edited by jonboy
Link to comment
https://www.sau.com.au/forums/topic/332430-need-advice/#findComment-5394254
Share on other sites

hello everyone :P

all different kinds of advice here... my advice is as follows.

when i was 19 i imported a non turbo Cefiro. i've had it nearly SIX YEARS.

like you - i got it when i was on my P's.

not because of legalities. i got the non turbo cefiro, because i wanted a mother effing cefiro. this car was nicer than ANYthing turbo going around at auction.

since then - i've made it an RB20de+T

(turbo'd the non turbo motor)

don't listen to people saying that turbo conversions are hard. they're not. not at all. and they're DEFINITILY not expensive.

now that i'm turbo. my car is fast. super duper fast.

stock turbo Rb20's have very low compression, and no torque, boost kicks in late in the powerband.

i personally am not a fan

MY setup however. boost is on at 2,500rpm, full boost is at about 3,500/4000.

it still revs out to 8 thousand, it still retains it's high compression, it has a conservatively small turbo setup using stock equipment.

it's rev happy

it's hyper responsive

it's more torquey than rb20det

you don't need to replace cams. you don't need to replace externals. just bolt on your parts and away you go.

everyone will tell you "you can't do it" or "it'll cost too much money" or "it will explode the internals"

i did my conversion four years ago. it cost me about a thousand dollars all up. and it didn't explode the internals. or the externals. infact it's travelled about 45,000 km as a turbo and hasn't missed a single beat.

so

if you want to buy a non turbo skyline. then do that.

if you want to turbo it. then do that too.

if you decide not to and sell the car. then do that.

it's your money.

imported cars are about heart.

do what your heart tells you to do. if only i was your age with the choice of cars that availabe for you guys now i'd be a happy man!

my advice is - don't do what ANYONE says. only ever do what James Quinn says.

another thing - if you get a turbo car soon like REAL soon you might find that you will receive a grace period because you bought the car before the laws... if you buy the car as an innocent young buyer and register the car innocently within the law at the time. the law can't punish you if they decide to change their mind.

check with Vicroads / RTA to confirm and make sure. but i reckon there would need to be leway

good luck!

Link to comment
https://www.sau.com.au/forums/topic/332430-need-advice/#findComment-5396371
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I had 3 counts over the last couple of weeks once where i got stranded at a jdm paint yard booking in some work. 2nd time was moving the car into the drive way for the inspection and the 3rd was during the inspection for the co2 leak test. Fix: 1st, car off for a hour and half disconnected battery 10mins 4th try car started 2nd, 5th try started 3rd, countless time starting disconnected battery dude was under the hood listening to the starting sequence fuel pump ect.   
    • This. As for your options - I suggest remote mounting the Nissan sensor further away on a length of steel tube. That tube to have a loop in it to handle vibration, etc etc. You will need to either put a tee and a bleed fitting near the sensor, or crack the fitting at the sensor to bleed it full of oil when you first set it up, otherwise you won't get the line filled. But this is a small problem. Just needs enough access to get it done.
    • The time is always correct. Only the date is wrong. It currently thinks it is January 19. Tomorrow it will say it is January 20. The date and time are ( should be ! ) retrieved from the GPS navigation system.
    • Buy yourself a set of easy outs. See if they will get a good bite in and unthread it.   Very very lucky the whole sender didn't let go while on the track and cost you a motor!
    • Well GTSBoy, prepare yourself further. I did a track day with 1/2 a day prep on Friday, inpromptu. The good news is that I got home, and didn't drive the car into a wall. Everything seemed mostly okay. The car was even a little faster than it was last time. I also got to get some good datalog data too. I also noticed a tiny bit of knock which was (luckily?) recorded. All I know is the knock sensors got recalibrated.... and are notorious for false knock. So I don't know if they are too sensitive, not sensitive enough... or some other third option. But I reduced timing anyway. It wasn't every pull through the session either. Think along the lines of -1 degree of timing for say, three instances while at the top of 4th in a 20 minute all-hot-lap session. Unfortunately at the end of session 2... I noticed a little oil. I borrowed some jack stands and a jack and took a look under there, but as is often the case, messing around with it kinda half cleaned it up, it was not conclusive where it was coming from. I decided to give it another go and see how it was. The amount of oil was maybe one/two small drops. I did another 20 minute session and car went well, and I was just starting to get into it and not be terrified of driving on track. I pulled over and checked in the pits and saw this: This is where I called it, packed up and went home as I live ~20 min from the track with a VERY VERY CLOSE EYE on Oil Pressure on the way home. The volume wasn't much but you never know. I checked it today when I had my own space/tools/time to find out what was going on, wanted to clean it up, run the car and see if any of the fittings from around the oil filter were causing it. I have like.. 5 fittings there, so I suspected one was (hopefully?) the culprit. It became immediately apparent as soon as I looked around more closely. 795d266d-a034-4b8c-89c9-d83860f5d00a.mp4       This is the R34 GTT oil sender connected via an adapter to an oil cooler block I have installed which runs AN lines to my cooler (and back). There's also an oil temp sensor on top.  Just after that video, I attempted to unthread the sensor to see if it's loose/worn and it disintegrated in my hand. So yes. I am glad I noticed that oil because it would appear that complete and utter catastrophic engine failure was about 1 second of engine runtime away. I did try to drill the fitting out, and only succeeded in drilling the middle hole much larger and now there's a... smooth hole in there with what looks like a damn sleeve still incredibly tight in there. Not really sure how to proceed from here. My options: 1) Find someone who can remove the stuck fitting, and use a steel adapter so it won't fatigue? (Female BSPT for the R34 sender to 1/8NPT male - HARD to find). IF it isn't possible to remove - Buy a new block ($320) and have someone tap a new 1/8NPT in the top of it ($????) and hope the steel adapter works better. 2) Buy a new block and give up on the OEM pressure sender for the dash entirely, and use the supplied 1/8 NPT for the oil temp sender. Having the oil pressure read 0 in the dash with the warning lamp will give me a lot of anxiety driving around. I do have the actual GM sensor/sender working, but it needs OBD2 as a gauge. If I'm datalogging I don't actually have a readout of what the gauge is currently displaying. 3) Other? Find a new location for the OEM sender? Though I don't know of anywhere that will work. I also don't know if a steel adapter is actually functionally smart here. It's clearly leveraged itself through vibration of the motor and snapped in half. This doesn't seem like a setup a smart person would replicate given the weight of the OEM sender. Still pretty happy being lucky for once and seeing this at the absolute last moment before bye bye motor in a big way, even if an adapter is apparently 6 weeks+ delivery and I have no way to free the current stuck/potentially destroyed threads in the current oil block.
×
×
  • Create New...