Jump to content
SAU Community

R32 Gtr - Wrecking / Parting Out. Alot Of Parts Available

Shano3000
 Share

Recommended Posts

Shano3000 Proficient

Shano3000

Posted
Posted (edited)

Parting out a gunmetal grey R32 GTR.

Most parts are available although parts that are NOT for sale include: Engine and all ancillaries, Engine loom, ECU, Crossmember, Front bar, Fenders, wheels, Front brakes and some other engine related parts.

Willing to post smaller items but bigger / heavier items are pick-up only from Emerald, Victoria or you organise a courier for pick-up from my address.

Everything listed is in good working order or otherwise stated.

Parts:

Gearbox - 150,000kms - $550

Injector resistor pack - $70

Front seats - Very good condition - Drivers has 1 very small hole and some wear on side bolster, passenger is perfect - $500

Rear Seats - Good condition $100

Nismo 260kph instrument cluster - showing 150,000k's - $200

Climate control unit - Top clip broken - $80

Centre gauges - Small crack (unnoticable once fitted) - $80

Fuel pump and assembly $100

Fuel tank $100

Passenger Door with window and door card - Paint in good condition $100

Passenger side Rear Tail light $50

Front Indicators - in perfect condition $50 each

Factory airbox (no snorkel, mounting bracket or filter) $150

GTR Grill $100

Stock FMIC $200

FMIC piping $100

Side Skirts - Drivers side has some cosmetic damage $100

Drivers Headlight $100

Rear Factory coilover - no leaking $100

Front Coilover - no leaking $100

Trust Gear Knob $25

Boot trim - $50

Rear Diff - $450

Tailshaft $100

Front shaft - $100

Front hubs and bearing assembly - $100 each

Rear hubs and assembly - $100 each

Rear callipers with rotors - plenty of meat left on pads and rotors $250

Brake master cylinder (ABS) - $80

Clutch master cylinder - $50

Brake booster - $80

Throttle cable - $60

Pedals - $30 each

Handbrake and cable - $50

Rear sway bar $50

Front sway bar $50

Seat belts x4 $100

Carpet - $50

Headlining - $50

Parcel shelf - $40

Radiator $80

Aircon condensor - $80

Also have alot of other parts including suspension arms, mounts, interior etc etc. Let me know what your after and i'll see what i can do. Also, sending me low ball offers will result in being ignored. Cheers

Edited by Shano3000
Shano3000 Proficient

Shano3000

Posted
  • Author
Posted (edited)

Skydie: It says my location in the post.

hoy32: Search for R32 GTR seats on Ebay. Ive listed them on there with pics.

Also have 3" Cat back exhaust. Has silencer and rear muffler so is rather quiet. $150

Edited by Shano3000
skydie Contributor

skydie

Posted
Posted

Skydie: It says my location in the post.

hoy32: Search for R32 GTR seats on Ebay. Ive listed them on there with pics.

Also have 3" Cat back exhaust. Has silencer and rear muffler so is rather quiet. $150

[/quot

Can i come have a look whats the address? msg to me 0431762826 cheers!

Tim GTR Proficient

Tim GTR

Posted
Posted
BWRGTR: Nope sorry.

talky: Nope sorry

frogman: same as this: http://www.nengun.com/greddy/ball-shift-knob in metalic

k-train: will do

Hi,

Will take the gear knob if it is available.

would you sell the two short franges 6 bolts ( tongues) seperate from the rear diff ?

pls call/sms o433 878905 Alex to arrange pick up or drop off

I am from Mordialloc 3195

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      V37 Radiator removal

      By Duncan · Posted

      So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You don't need to drain the intake heat exchanger to remove the radiator but depending on your plans you may need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • MBS206
      Unpeeling the Orange

      By MBS206 · Posted

      If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      LOL, all of the CAI like Craig I just need to put a hole saw through my bumper Done and dusted, the car runs, which is nice, I'll take it for a spin when the weather clears up Just need to put the bumper back on for good
    • EndZee
      R33 Gts/-t Abs Module Wiring Schematic (not Gt-r)

      By EndZee · Posted

      Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • GTSBoy
      Boost cut after swap(RB25DET NEO) R34

      By GTSBoy · Posted

      Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
×
×
  • Create New...