Jump to content
SAU Community

Recommended Posts

Wrecking complete Late 1991 GTR except engine, Happy to post or courier, Brisbane based Feel free to PM, text or call leave message if I can’t answer. 040818877. If someone is low hassle nice & fair I am happy to help. I have a day job so I am no car expert just enjoy Nissan's, please describe requests. Off the cuff questions please PM.

Panels

Guard Driver side 275

Left door 200

Side Skirts 250

Window mechanism 100

Rear Bumper 175

Rear Reo 175

Glass

Rear windscreen with all wiring, Genuine thinner and lighter 525

Light & Indicators

Tail Light Passenger side 75

Tail Lights Driver side 75

Interior great condition

Centre Console with lid 135

Roof lining perfect 90

Gauges

Greddy Exhaust gauge and wiring 120

Climate Control 90

Drive Line

Gear Box 33 GTR Good condition fits 32 as well 850

Front Diff 250

Rear Cradle 400

Tail shaft 200

Suspension

Lower control arms factory with N1 brake ducting 100

Rear hubs 130

Engine Bay

ABS Unit 290

Brake Master cylinder 150

Power Steering Reservoir 90

Coolant bottle

Blow off Valves 175

Fuel Door 50

Fuel tank $40 90

Front sway bar 90

Front LCA (pair) 200

4WD Computer 150

Engine Harness $600 new 120

Injector & resistor pack 120

Air flow meters 145 Each

HKS air pods 80 Each

Centre Console 160 set

Leather Genuine 90

Exhaust 400

Feel free to PM, text or call leave message if I can’t answer. 0408188777

post-34523-1282553441_thumb.jpg

post-34523-1282553458_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/333969-wrecking-non-damaged-32-gtr/
Share on other sites

hey man whats the price on the fuel tank? you've got 2 on the ad. does the tank come with the fuel pump. is it complete?

Sorry mate bad cut and past woudl do for 80 not including pump

Cheers

Hi

Sorry for the delay in text messages I had a back up and a bunch came thru all at once. Just to clarify items available are from the list above injectors have been sold. There is some of the smaller parts that I have not listed

Cheers

  • 2 weeks later...
  • 2 weeks later...
  • 1 month later...

anyway I can get a look at what is left of this car? shoot me a PM.

Hi Chris

Sorry I cant work ut how to send PM's on the new format, just send me a lsit of what you are after.

Update front hubs are sold

Cheers



  • Similar Content

  • Latest Posts

    • Did and sync timing with light 
    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
×
×
  • Create New...