Jump to content
SAU Community

Recommended Posts

Here is one on an 8" rim. You can also see the wear indicators clearly. They're virtually new.

They DO typically come looking a bit grubby due to rubber pickup on the "tread" face, but don't let that worry you. The indicator shows the true depth.

215slick.jpg

And here is the "dunlop" and "japanese text" on the sidewall (look closely)

215mini.jpg

Edited by Marlin
I've used the Mini ones for 270klm at Lakeside so far (at 10/10ths), and the worst of the four is maybe one third worn.

They were virtually new (maybe 5/6 laps) when I got them and they cost me $100 each plus some freight to me from Melbourne. I since found I can get in Bris for $75 each. LOL

Dan, two sets of wheels means you drive to the track and bolt on the second set that were in the boot and back seat with proper race tyres, slicks even. IMO you are over-wheeled with 9 inch rims on that car.

The Mini Challenge tyres are Dunlops, size is 215/45/17, but I measured them because they looked so much bigger, and turns out they are nearly identical in size and width to my Dunlop and Kuhmo 235/45/17's.

link link this place that sells them for $75 each <3

If you get some second hand semi's, try putting some GRIP tyre softener on them. Be careful where you apply it though, it absolutely stinks!

does this stuff work on road tyres? my current set, especially the rear feels a bit too hard. not gripping anywhere near what they should be.

Edited by Peter89
link link this place that sells them for $75 each <3

does this stuff work on road tyres? my current set, especially the rear feels a bit too hard. not gripping anywhere near what they should be.

Not sure mate...

I've used the Mini ones for 270klm at Lakeside so far (at 10/10ths), and the worst of the four is maybe one third worn.

They were virtually new (maybe 5/6 laps) when I got them and they cost me $100 each plus some freight to me from Melbourne. I since found I can get in Bris for $75 each. LOL

Dan, two sets of wheels means you drive to the track and bolt on the second set that were in the boot and back seat with proper race tyres, slicks even. IMO you are over-wheeled with 9 inch rims on that car.

The Mini Challenge tyres are Dunlops, size is 215/45/17, but I measured them because they looked so much bigger, and turns out they are nearly identical in size and width to my Dunlop and Kuhmo 235/45/17's.

OMG , can you share with us how to buy those slicks, I am attending a track day soon, desperately looking for some used cheap track tyres=)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...