Jump to content
SAU Community

"play" In The Driveline

s13-steve
 Share

Recommended Posts

Missileman Veteran

Missileman

Posted
Posted

Same problem here in an R32 GTR - clunks from the rear when driving harshly, so I put it over the pit and it has a ridiculous amount of play which we isolated to the rear diff. Next, is to remove the centre and get it rebuilt at a shop.

On that does anyone know a good place to go for a diff centre rebuild in Perth?

Do report back what they did to fix it and the cost, I have a similar issue with my R32 gtst.

Mike.

  • 2 years later...
V28VX37 Veteran

V28VX37

Posted
Posted

Resurrecting an old thread.

I'm experiencing some play in the driveline after my recent manual conversion, two different types:

  • There's a slight but noticeable 'clunk' on gear change (clutch-in). This happens most of the time but not always, and doesn't seem to be related to a specific gear or speed. This is the one I'd like to get fixed.
  • There's also slight 'slack' when changing over from accel to decel or vice versa. This feels quite similar to other manual cars I've driven but I'm not sure how 'tight' it's meant to be with an RB25DET gearbox?

I had a look under the car, I could rotate the front part of the tail shaft probably 2mm by hand, the rear part was harder to move. This is with the car in gear and handbrake on.

Which part of the driveline should I look at first?

What's the best way to check the condition of the tail shaft centre bearing?

GTSBoy Grand Master

GTSBoy

Posted
Posted

From your symptom description I would suggest the centre bearing the tailshaft would be #1 suspect.

In reality, I find that it is every single point in the driveline adding up. I have play in the tailshaft, some in the diff, some in the rear CVs and some in the rear hubs. Not enough at each point to be concerned about, but added together they create a hell of an annoying clunk in my driveline.

V28VX37 Veteran

V28VX37

Posted
Posted

Thanks GTSBoy, I'll start from there! I wouldn't be surprised either since the tailshaft is a combination of my R34 sedan rear half and an R33 coupe front half from the wreckers.

Just a couple of more observations from today:

  • There's a slight but noticeable 'clunk' on gear change (clutch-in). This happens most of the time but not always, and doesn't seem to be related to a specific gear or speed. This is the one I'd like to get fixed.

This seems to come from behind the driver i.e. centre bearing, diff, or drive shafts. Centre bearing is currently the prime suspect.


  • There's also slight 'slack' when changing over from accel to decel or vice versa. This feels quite similar to other manual cars I've driven but I'm not sure how 'tight' it's meant to be with an RB25DET gearbox?

This seems to be more in the front side so clutch or the gearbox itself. I reckon it's the latter.

I'm not too fussed about this one but the clunk on gear change is more annoying so need to get that sorted.

  • 2 weeks later...
V28VX37 Veteran

V28VX37

Posted
Posted (edited)

I just checked this again with handbrake on and gearbox in neutral. There's about 8mm of play in the diff, measured on the outer ring where the tail shaft joins the diff. Not sure if this is a little or a lot?

I also did the 'diff test' and opposite wheel rotates the same way when turning so it's definitely is viscous diff. Might be time to upgrade...

Edited by V28VX37
  • 8 years later...
elohim_imanu Contributor

elohim_imanu

Posted
Posted

Most of my play is in the half shafts. What do people do about this? OEM are pretty expensive. Like $1,600 each.

I can rotate a wheel about 15-20mm at the outside of the tyre, is this too much?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • jtha7
      Replacing turbo water line - any recommendations or advice?

      By jtha7 · Posted

      Hi all, Restoring r33 series 1 rb25det. All the heater hoses were on their way out, have replaced them and put it all back together. After testing I noticed a small leak from behind the head on the actual metal water line to the turbo when cars warm. I tried running a longer hose over it but it kept leaking...   I am about to take the (stock) manifold off again😔 to change the water line does any one have any lines they recommend? I was looking at Aeroflow Turbo Oil & Water Line Set but not sure what everyone else recommends. Car is completely stock but want to upgrade turbo eventually. it looks like ill have to disconnect a lot just to replace these lines so if there's anything else recommended to do please let me know. Thank you in advance!
    • MBS206
      RB20DE NEO smallbox clutch.

      By MBS206 · Posted

      From memory, on the R33 GTSt at least, while everyone says "It's not adjustable", I found when I changed clutches in mine, it just needed a small adjustment on the rod length. But be very wary here, as you could end up trying to push the pushrod in the master too far, or blowing out the slave.   Most likely though, if the master/slave isn't bypassing internally or leaking out, then the throw out is the wrong height compared to the fingers on the clutch, so when it moves to disengage the clutch, it isn't 100% disengaged. You can check part of this out too by jacking the car up, having the engine running, put your foot on the clutch and try to engage 1st gear. If it goes in pretty easy (Compared to the ground) and/or the wheels start turning a fair bit and it takes a bit too much brake pedal to bring them back to a stop, this is likely the issue.  I'm not sure if you can adjust the height of the forks etc in these though, it's been that long since I've touched any RB gearbox.
    • MBS206
      Lock up the old for sale / wtb threads.

      By MBS206 · Posted

      That's all good, I thought I was missing some interesting feature! Maybe @PranK can double check if that is something that is meant to be operating or not.
    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      I hope that is not something that bad. From what i remember he said that only first gear is "hard" to get in and that he has couple of ideas what to try next but idk 😕  hope it is not gearbox out. I will let you know.
    • GTSBoy
      RB20DE NEO smallbox clutch.

      By GTSBoy · Posted

      If it's not the hydraulics, it is probably gearbox back out. Usually as per @Duncan's post, or otherwise associated with not getting the throwout fork positioned correctly. All the way up to catastrophically bolting shit back together without it being aligned properly and wrecking the clutch/input shaft/flywheel/something else.
×
×
  • Create New...