Jump to content
SAU Community

Recommended Posts

There are plenty of kits out there on the market, both Jap & US kits will do.

I will be fitting the Stillen gen 2 true dual system to my car tomorrow.

Best option would be to spend the money and get your zorst from a recognised manufacturer as they have spent the time and money to R&D a proper system.

If you go get a custom done here at your local pipe bender, you will more than likely end up with a drone. :starwars:

Edited by pv35gt8
Like the topic header thinkin of gettin an exhaust for my V35 sedan , has anyone had any experience with them? are this kits for the US G35 suitable for a V35? or is the best way to go custom? Any advice is appreciated

The G35 sedan exhausts should fit, but IMO you can't really go past an exhaust from one of the major Japanese makers (Fujitsubo, Weldinum/Nismo, Kakimoto etc).

Having said that, I will be more than happy to be proven wrong by James' Stillen system tomorrow (you forgot to mention that we are doing your extractors as well mate! Aren't they Tomei?)

true so what places are there here to get the bits from ??

Yep, as below... Yahoo Auctions.

For exhaust stuff, I use Import Monster and have it shipped by sea in one of their containers.

They will then ship it to your door for a good price.

Alternatively you could always request RHDJapan to list the part and buy it through them.

yahoo.jp

fujitsubo from $800 + $250 delivery

:P

I was lucky enough to have something like this upon purchase on my 300GT Sedan.

http://www.nengun.com/impul/blast-ii-muffler

I don't know alot about this but my car is only single exaust and sounds nice and quite responsive.

Maybe I have the Blast 1 ?

Not sure if I meet EPA levels either ?

There are plenty of kits out there on the market, both Jap & US kits will do.

I will be fitting the Stillen gen 2 true dual system to my car tomorrow.

Best option would be to spend the money and get your zorst from a recognised manufacturer as they have spent the time and money to R&D a proper system.

If you go get a custom done here at your local pipe bender, you will more than likely end up with a drone. :action-smiley-069:

how does the stillen system go?

The Buddy Club will be loud

I don't know anything about Megan Racing.

Very, very tough to go past a Fujitsubo exhaust.... in any car! Not to mention that it will be a guaranteed bolt on upgrade.... as opposed to fighting with something that the Americans call "bolt on"... aye James?

as opposed to fighting with something that the Americans call "bolt on"... aye James?

Yes the Stillen was a bit of a fight to line up, but we got it there in the end.

The lovely note it produces was worth the effort :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • @Murray_Calavera  If I were an expert I wouldn't be in here looking for assistance.  I am extremely computer literate, have above average understanding on how things should be working and how they should tie together.  If I need to go to a professional tuner so be it, but I'd much rather learn and do things myself even if it means looking for some guidance along the way and blowing up a few engines. @GTSBoy  I was hoping it would be as simple as a large vacuum leak somewhere but I'm unable to find anything, all lines seem to be well capped or going where they need to be, and when removed there is vacuum felt on the tube.  It would be odd for the Haltech built in MAP to be faulty, the GTT tune I imported had it enabled from the start, I incorrectly assumed it was reading a signal from the stock MAP, but that doesn't exist.  After running a vacuum hose to the ECU the signal doesn't change more than 0.2 in either direction.   I'll probably upload a video of my settings tomorrow, as it stands I'm able to daily drive, but getting stuttering when giving it gas from idle, so pulling away from lights is a slow process of revving it up and feathering the clutch until its moving, then it will accelerate fine.  It sounds like I need to get to the bottom of the manifold pressure issue, but the ignition timing section is most intimidating to me and will probably let a pro do that part.  Tomorrow I'll try a different vacuum line to T off of, with any luck I selected one that was already bypassed during the DBW swap. @feartherb26  I do have +T in the works but wanted to wait until Spring to start with that swap since this is my good winter AWD vehicle.  When removing the butterfly, did it leave a bunch of holes in the manifold that you needed to plug?  I thought about removing it but assumed it would be a mess.   I notice no difference when capping the vacuum line to it or letting it do its thing.  This whole thing has convinced me to just get a forward facing manifold when the time comes though.
    • Update: tested my spark plugs that are supposed to be 5ohms with a 10% deviation and one gave me a 0 ohms reading and the rest were 3.9ohm<, so one bad and the others on their way out.
    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
×
×
  • Create New...