Jump to content
SAU Community

Recommended Posts

Hey guys, got my sisters r33 here with a stuffed radiator. Some info on when the problem started.

Her car has been sitting in my backyard for the past year and a half because it was un registered and clutch was stuffed. Got new clutch in and got it registered again. The car has always had an odd problem where you had to keep the rad cap slightly opened otherwise the car will overheat and the overflow bottle will start to bubble. The other week, the heater core gave way and hot coolant went everywhere and fogged up all the windows.

She brought the car over so I bypassed the core because she doesn't use the heater anyways. I topped up the coolant, bled it, all was good. Then a couple days later, the car overheated and overflow bottle bubbled up again. Took the car to natrad and the guy sold us a new rad cap as the seal on the old one was buggered. He told us to bring it back if it does it again.

Car did it again, so I pulled the rad out (funds are a little low so cant afford to get natrad to fix it) and as I was pulling the hose off, the spot where it slips onto snapped off. I stuck a hose in the rad and all this brown shit came out. Ive been flushing it out for the past 3 days and the gunk wont stop. Black chunks are also coming out so I think its safe to assume the radiator was blocked and corroded to death. I removed the thermostat and put it in a jar of boiling water and it opened fully. I tried looking for a thermometer to check if its opening at the correct temp (I think its meant to be 75 degrees?) but cant find a thermometer that goes above 50 :D I was just going to buy one just incase but they arent very cheap. I also flushed the engine with the hose and luckily it was clean and not a spec of gunk in it.

Now some questions.

1. Ebay china intercoolers. I found this one on ebay for $125 + 80 for shipping. Are these rads any good? or should I buy a new original type from somewhere?

2. The thermostat. If its opening fully from water straight from the kettle, is it safe to assume that its working correctly? If I dont have to buy one, it would save me some money to buy new hoses instead. Im guessing they are the original ones as the clamps have dug into them pretty badly and I dont think they will survive another clamping.

3. Whats the chances of the water galleries in the engine been blocked? there was no gunk in it and the flow was nice and steady.

I apologize for the wall of text lol. My sister hasn't had the car for so long and she misses it. She has my 300zx to keep her company though lol

One step at a time, firstly, take your radiator to a radiator shop/guy and get him to clean and pressure test it

Then buy your hoses and set the radiator up with proper coolant again. It sounds like your thermostat is working OK, may not be the right one but you'll have to work with it for now and see - the radiator guy may be able to help. If your sister is a bit of a looker have her 'help' you drop the stuff off, you might get a slightly better deal????

Ebay radiators are probably Ok for a 'Get out of Jail Free' card, but don't be surprised if they don't fit as well as your std one - also phone up Just Jap or go to their Trader section in the For Sale section of SAU on here and send them a PM, they have chinese alloy radiators and although the quality might not be Greddy spec, they would be OK and at least will fit plus you'd get some warranty and/or support.

I'd doubt that the water galleries in the motor would be blocked, it would take a fair bit for that to happen.

The only other part of this equation is your water pump? And you can pick one up on ebay for under $80 [last i looked] and they work.

I think the water pump is ok because when I would rev the car with the radiator cap off, the water would get sucked in and then come back up when it idles. I might check out justjap and see how much their alloy rads are. Id rather not waste my time with the old rad because its broken and plus a constant flow of crap comes out.

A good mate who is a well renowned mechanic has a cheap china radiator in his 180, which is running 260+rwkw, and he swears by it, bought it as a "get out of Jail" and fitted perfectly, inc original shroud etc, and has not had 1 prob with it.. With that much trouble though I would be worried the issues go further than the radiator...

Im thinking the same but as trident said only other thing could be water pump but to me it looks like its working fine. Im going to end up buying the ebay one (actually found a 52mm for around the same price) I added some cash into my canvas card and wating for it to clear.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...