Jump to content
SAU Community

Recommended Posts

that's fine for others to do but i wont ask others to lie on paperwork saying I'm only receiving so many $$$ of parts and trick the government out of tax

pretty sure they would send in separate parcels to keep it all above board

Link to comment
https://www.sau.com.au/forums/topic/337085-e85/page/5/#findComment-5454974
Share on other sites

  • Replies 92
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

you wouldn't have to change rails again Mark

and for injectors it depends on how much headroom your current ones have in the tune you currently have

Pete quite possibly, but someone else can organise it i got to much to do already thinks of @ least 2 events that need organising

Link to comment
https://www.sau.com.au/forums/topic/337085-e85/page/5/#findComment-5455089
Share on other sites

feelings ey.... well im upset with life because..... oh feelings about e85. im sitting on the fence till it becomes more common.. not really down with changing rail and injectors just yet, already done it once :cool:

if its for the gtr then the top feed 1000's are around $600 delivered. and they use the std fuel rail. 1600's I think require the bigger fuel rail - you'd have to ask LukeENR34 if his 1600's fit into the stock rail - and theyre around $850 or something delivered

** depending on exchange rates, cc capacity, types of injector and impedance

-D

Link to comment
https://www.sau.com.au/forums/topic/337085-e85/page/5/#findComment-5455459
Share on other sites

if its for the gtr then the top feed 1000's are around $600 delivered. and they use the std fuel rail. 1600's I think require the bigger fuel rail - you'd have to ask LukeENR34 if his 1600's fit into the stock rail - and theyre around $850 or something delivered

** depending on exchange rates, cc capacity, types of injector and impedance

-D

dohmar can you get 1000cc side feed injectors for standard rb 25 rail?

Link to comment
https://www.sau.com.au/forums/topic/337085-e85/page/5/#findComment-5455480
Share on other sites

no idea sorry - best to ask willall or any other tuner/member who actually runs e85 - i just run 98ron

-D

no worries will do, going to move to e85 eventually, probably purchase some injectors from you at some time in the future. Still in research stage at the moment.

Link to comment
https://www.sau.com.au/forums/topic/337085-e85/page/5/#findComment-5455566
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I'm with you here. It's either loom has an issue, OR, injectors are not functioning properly. It could even be they're just constantly dribbling, hence the wet, but not firing.
    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
×
×
  • Create New...