Jump to content
SAU Community

Wheels,seats,fmic

Autumn33

By Autumn33,
in Tasmania

 Share

Recommended Posts

Autumn33 Mentor

Autumn33

Posted
Posted

17" Osaka ENZO 17x7 Brand New only test fitted

Multi fit 5 stud Wheels - 5x114.3 & 5x100

Hyper black with machined lip

No Tires

Asking Price:$700 Firm

-----------------------------------------------------------

FMIC

600x300x100 with 3inch inlet/outlet has a few bent fins

Asking Price:$100 firm

------------------------------------------------------------

Pair of Black Zenzo Racing seats

great cond with no rips or tears but one is a little faded

Asking Price: $300 firm

post-71390-1285040384_thumb.jpg

post-71390-1285040405_thumb.jpg

post-71390-1285040421_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/337620-wheelsseatsfmic/
Share on other sites
Autumn33 Mentor

Autumn33

Posted
  • Author
Posted

also have a Xbox 360 (not slim) 20gb hdd, controller comes with forza 3 & street fighter iv

only bad point is it need a face plate as the one i have is broken @ the power button but it still works fine i just turn it on with controller

Asking Price: $120 obo

Link to comment
https://www.sau.com.au/forums/topic/337620-wheelsseatsfmic/#findComment-5459210
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By GTSBoy · Posted

      I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
    • WMDC35
      Wheel Sizes & Offsets For Skylines

      By WMDC35 · Posted

      A bit late but A disk S13P fit over stock R32 GTR brakes, usually A disk front, O disk rear works.
    • Duncan
      RB20DE NEO smallbox clutch.

      By Duncan · Posted

      Or, the height of the release bearing is not correct for your combo. Start with the bleeding and checking the slave moves throughout its range when you press the pedal (2 person required), but it is possible for the height to be internally wrong too (box back off to measure.
    • GTSBoy
      RB20DE NEO smallbox clutch.

      By GTSBoy · Posted

      Yes, there's quite a few things that can go wrong during a clutch install. Very unlikely. I have a similar clutch. They (ACS) make good gear. No, it is not normal. It is possible that you just need to bleed the clutch slave. But the new clutch will also have a more aggressive actuation force/pressure, and so your old slave cylinder might be a bit leaky or otherwise compromised, and not up to the extra force required. Or the master cylinder, same.
    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
×
×
  • Create New...