Jump to content
SAU Community

Recommended Posts

so my stock castor bushes are shagged... and will need replacing...

ive heard of a fair few wheel aligners not being botherd to play around with the polyurethane bush ones

are these ones a better option... or just too shit to even worry about?

http://cgi.ebay.com.au/ws/eBayISAPI.dll?Vi...e=STRK:MEWAX:IT

these ebay ones are obviously going to make it more appealing for them to play with... or do i need to get my self a legit wheel aligner lol...

Link to comment
https://www.sau.com.au/forums/topic/339059-castor-options/
Share on other sites

they looks alright i think i need something like this also

always easier to adjust to spec than bushes however not regency friendly (unless engineered).

The ball mount makes cornering a little sharper on initial turn in, but if u got a gtr/gts4 u need them with a bend in a specific place

I'll grab these cuscos from nengun when i get around to it. jjr do their own version for $200 but when it comes to suspension parts i dont really wanna skimp

http://www.nengun.com/cusco/adjustable-pillow-tension-rods

more + caster = better turn in (at least in my case)

-D

Link to comment
https://www.sau.com.au/forums/topic/339059-castor-options/#findComment-5477538
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Dredgggggeeee time; I have recently finally started driving the car. It sat for so long that the fuel tank gave birth to rust sludge and blocked my lift pump sock and one of my walbro 460's and left grime, rust chunks and muck all through the surge tank and system. I decided to commit and pull the trigger on an oem r32 gtr fuel tank and Frenchys twin 460 / sender / surge tank hanger combo and all new larger lines and fittings etc, also boost doc heater hose kit / new heater core and a heap of other bits and shits like wideband sensor installed in the dump and Syltech iacv + lines and all wired and added to current tune. now having lightly driven it a couple times without issue, I can happily report on the hta3076 in its current tune. still no boost control switched on, 20psi gate springs, car makes 22psi at 3200rpm in 6th gear with 30-50% TPS from cruise at 100kmh. Going by the old graph, this means it should be making 300-325whp at the same numbers above. Very very responsive setup under true road driving loads. all that's left for the build is body loom + PDM, finish the remote aircon setup, install carbon fibre parts and go for full tune and 30psi. the 315 rear tyres are now performing like they're 195's, wheel spin in any gear at almost any rpm, whereas my previous setup hooked up in 3rd no issue, albeit Nt01's back then / RB25 5spd vs (new) old date r888r's Z34 6spd now, + obviously all the support upgrades I listed in the quoted post above. car sits at 1-3psi on cruise at 100kmh, expectations totally exceeded and I'm beyond stoked with all this so far. IMG_4848.mov
    • I've also been eyeing their rear axles for my car. I purchased seat mounts from them about 7 years ago and they were hot garbage so I've been a little wary about purchasing them. With that being said, please buy them and get back to us haha. 
    • Can a moderator please move this into the right category.. I've accidently put this into racing build thread 🤦🏽‍♂️
×
×
  • Create New...