Jump to content
SAU Community

How To Reach Back Speakers In A R34 Gt

335

By 335,
in Car Audio & Electrical

 Share

Recommended Posts

Carbon 34 Grand Master

Carbon 34

Posted
Posted (edited)
Hello

How do I reach the speakers in a R34 GT to remove them? How do I fold down the back seat or take out the top part of the back seat?

Help

2dr version

remove the two bolts on seat bottom cushion, remove bottom by sliding forward and off the seat belts catches

remove bolts on seat belt bottom part where they meet the floor pan, for ease of rear deck removal

two bolts on seat back on each corner, then slide straight up but watch the window cause it will scratch tint if your not careful

rear deck is held on by sliding under each side into a notch from the sail panels and two plastic plugs underneath in the middle, those can just pop up with care , also 3 plugs on the front of the shelf lip need to come off

two seat belt moldings need to have the seat belts slide thru them to remove the rear deck, which is why you took out the seat belt lower bolts

rear deck needs to flex down a tiny bit on both corners and up in the middle to remove once everything is loose/removed

speaker grills might need to come off from inside the boot, depends on whats in it now

and maybe a cover for the wiper on some cars , mine was removed with new fiberglass molded deck a while ago

some decks have baby bolts , 3 of them, to remove, some screw from underside in the boot, but once you get the seat out you can see near the shock towers on how they have them mounted ?

to completely access the underside of the rear deck you just remove the plug on the top of the carper liner hiding the seat back in the boot side. the other parts are in the spare tyre well and just pry off with the right tool. forked plastic or metal removal tool or they will break

bolt area on seat bottom

above

bolt area on seat back below

think thats it if I remember right..lol hope that helps. kinda a pain depending on what is in it now ???

some cars have aftermarket speakers already and this will vary on mounting.

Edited by sapphiregraphics

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      remote oil cooler hose size, 8,10 or an12?

      By GTSBoy · Posted

      I will rebutt this and the preceding point from Dose....but without doing any calcs to demonstrate anything and without knowing that I am right or wrong. But... The flow capacity of a fluid transfer system is not limited by the smallest orifice or section of conduit in that system, unless it is drastically smaller than the rest of the system. OK, I use the word drastically perhaps with too much emphasis, but let's drill down on what I really mean. The flow capacity of the system is the result of the sum of the restrictions of the entire system. So, to make an extreme example, if you have a network with 3" pipe everywhere (and let's say a total length of only a few metres) and that 12mm ID restriction of the oil filter connection being the obvious restriction, then for any given amount of pressure available, the vast majority of all the pressure drop in the system is going to occur in the 12mm restriction. But.... increase the length of the 3" pipeline to, say 1000m, and suddenly the pipe pressure loss will likely add up to either be in the same order of magnitude, possibly even exceeding that of the 12mm restriction. Now the 12mm restriction starts to matter less. Translate this to the actual engine, actual oil cooler hose sizing, etc etc, and perhaps: The pressure loss caused by flowing through the narrow section (being the 12mm oil filter port, and perhaps any internal engine oil flow pathways associated with it) is a certain number. The pressure loss through, say, -12 hoses out to the cooler and back is negligible, but The pressure loss through -10 hoses out to the cooler, at the exact same length as the above, starts to become a decent fraction of the loss through the 12mm stuff at the filter port. Maybe even it starts to exceed it. I could actually do these calcs if I knew 1) how much oil was actually flowing in the line, 2) gave enough of a f**k to do things that I hate doing for work, voluntarily for a hypothetical discussion. Anyway - I reiterate. It's not the narrowest port that necessarily determines how much it can all flow. It is the sum. A long enough length of seemingly fat enough pipe can still cause more loss than a semmingly dominant small bore restriction.
    • MBS206
      remote oil cooler hose size, 8,10 or an12?

      By MBS206 · Posted

      To pick up what Dose is putting down. Not a lot of point running a huge hose if the motor is still restricted to the smaller size... It's only capable of flowing so much at that point...   *Waits for GTSBoy to come in and bring in the technicalities of length of pipe, and additional restriction from wall friction etc etc*
    • QB6SAGR
      Tein Circuit Master- rebuild worth it?

      By QB6SAGR · Posted

      Hooley Dooley these things have some history! If i sell them they will need a certificate of providence to prove they have been in the hands of verified RB20 royalty! They have been stored in a plastic tub, away from sunlight and moisture. They are in mint condition. And they will stay that way, as i have sprung the money for a set of shockworks coilovers. I'm just working on getting them in at the moment, after rebushing the rear of the car, and while the subframe was out i welded in the GKtech reinforcement bracing as well.  They will get a workout at Ararat King of The Hill in November. I ran 48s on the short course there a few months ago, and i am hoping with new bushes and shocks in the rear i can launch a bit harder. There was a fair bit of axle tramp when i tried too hard off the line. a few of the corners had dips mid way which also made the car feel a bit unsettled, hopefully this will help there too.   
    • Dose Pipe Sutututu
      remote oil cooler hose size, 8,10 or an12?

      By Dose Pipe Sutututu · Posted

      Food for thought, the stock oil filter thread is a 3/4-16 UNF, which has an ID of about 10 to 12mm (according to ChatGPT lol). Now compare than to an 10AN, which has an ID of about 14mm (Raceworks is 14.2mm, Speed flow is 14.27mm).  
    • MBS206
      Dose's Sometimes DIY and Pay Someone Home & Boat Improvement Thread

      By MBS206 · Posted

      Yep, totally get that. However hooking in for Generator back up is only a few hundred bucks for the wiring. You could put a couple of those in (for different circuits explicitly) and run a couple of baby generators. Bonus, you can balance them across different circuits, and now have backups in your backup. I'm looking at buying places that won't even have water etc, and I don't mind the idea of getting off the electric grid either, even with everything you've said. This country already has enough power outages that even the mains grid isn't that reliable anymore. I do agree though on spending a bit more to get better gear, and to add some extra redundancy in to the system too.
×
×
  • Create New...