Jump to content
SAU Community

Recommended Posts

russ's car?

Yep.

also is it better to get my cams license insted

not sure if all tracks accept aasa for future events

and i left my memb no. empty cos i dont have one yet is that ok?

If you want to do anything other than winton and Deca then get a cams licence. It costs more though. Get it sorted sooner rather than later.

That sold out in record time!

No where near a previous one a few years ago. It was like 45mins!

  • Replies 165
  • Created
  • Last Reply

Top Posters In This Topic

My forms should have been faxed through now. ._.

Payment already made, as per my previous posts.

If I don't make it into this one, can payment go towards the next DECA or whatever? :blush:

send a PM to Belsil80 and your money will be refunded.

ppl will drop out. they always do so maybe hang on for a little bit?

as ppl drop the reserves make it in and those that didnt make the reserves get a spot in the reserve.

Entry Form & Supp. Regs. : SOLD OUT

FILL OUT FORMS COMPLETELY. INCOMPLETE FORMS WILL NOT GO ONTO ENTRY LIST.

***Also, if you are emailing you entry, please name the attached file after your full name and what page it is. eg. 'Ryan Bell Disclaimer'.

Event Schedule: Not yet available

Results: Not yet available

All withdrawles will be refunded after the event. Refunds will not be given after 5pm Monday 15th November.

That's what special guest appearances by the Fang Artists will do for ya. We're hyped. With the exception of Ash & Dave coz they may not have vehicle of choice at the time. In fact, Ash has NO chance :blush:

Sorry, who are the Fang Artists? Are you guys like painters or sculpters? :D

Rule 1 of Fang Artists: Don't talk about Fang Artists

Rule 2 of Fang Artists: See rule 1.

Apparently word has it that back in the day, they all had sweet rides. That is until most of them grew up and had families.

They still do the occasional Sunday lunch together and go to garden shows when time permits.

Sorry, who are the Fang Artists? Are you guys like painters or sculpters? :P
Guest
This topic is now closed to further replies.



  • Latest Posts

    • If you take the top half of the intake off you can unbolt the flap off the shaft and leave the shaft in there blocking the hole. Then you can remove the little vacuum canister off from under the manifold and get a spare vacuum line to run to the ECU. I can take some photos of it later. Probably best to get the vacuum source to the ECU sorted first though. Mine all worked mint with the base map from the GTT an I've pretty much let the closed loop sort the fueling and took 1 degree out of the whole timing map.
    • This IS something you also have to configure in Haltech (or at least I did in the past when going from onboard-to-ECU map sensor and an external MAP sensor in haltech land).
    • I'm hoping it's something as simple as the ECU is looking for an external MAP sensor, but he is trying to use the onboard MAP sensor.
    • You won't need to do that if your happy to learn to tune it yourself. You 100% do not need to do that. It is not part of the learning process. It's not like driving on track and 'finding the limit by stepping over the limit'. You should not ever accidently blow up an engine and you should have setup the ECU's engine protection to save you from yourself while you are learning anyway. Plenty of us have tuned their own cars, myself included. We still come here for advice/guidance/new ideas etc.  What have you been doing so far to learn how to tune?
    • Put the ECU's MAP line in your mouth. Blow as hard as you can. You should be able to see about 10 kPa, maybe 15 kPa positive pressure. Suck on it. You should be able to generate a decent vacuum to about the same level also. Note that this is only ~2 psi either way. If the MAP is reading -5 psi all the time, ignition on, engine running or not, driving around or not, then it is severely f**ked. Also, you SHOULD NOT BE DRIVING IT WITHOUT A LOAD REFERENCE. You will break the engine. Badly.
×
×
  • Create New...