Jump to content
SAU Community

Recommended Posts

Im abit confused about the soild lifter type mentioning..

P90 are L28et ?

There is a head, or was a head in USA, a P90A which had hydraulic lifters (non adjustable) but they are useless today, because the lifter is no longer available if one fails and they were sealed and unserviceable.

Cheers, D

P90 with dished pistons are L28ET, P90 with flat-top pistons are L28E. Not very common here in Aus (but I have 2 of them :P ).

The P90 L28E was matched to the F54 block - which was the 'last hurrah' of the L-series sixes.

P90 with dished pistons are L28ET, P90 with flat-top pistons are L28E. Not very common here in Aus (but I have 2 of them :worship: ).

The P90 L28E was matched to the F54 block - which was the 'last hurrah' of the L-series sixes.

I have a F54 Block, but it's only got a N42 on it, Still looking...

I have the F54/P90 combination with flat top pistons, but the motor was imported out of Japan, as it also has the dual stage throttle body on the L28E manifold.

Depending on your application, the F54 block is not necessarily the best block for the job.

eg; the best block to use for the L31 build is the N42 and not the F54 as commonly thought. I have sonic tested 6 plus F54 blocks and if any were to be used in a plus 3.0mm overbore, the cylinder walls would probably have been porous. Hence why I decided to use my block with a max oversize bore of 1.0mm.

Any particular reason you want an F54/P90 combination?

Cheers, D

I have the F54/P90 combination with flat top pistons, but the motor was imported out of Japan, as it also has the dual stage throttle body on the L28E manifold.

Depending on your application, the F54 block is not necessarily the best block for the job.

eg; the best block to use for the L31 build is the N42 and not the F54 as commonly thought. I have sonic tested 6 plus F54 blocks and if any were to be used in a plus 3.0mm overbore, the cylinder walls would probably have been porous. Hence why I decided to use my block with a max oversize bore of 1.0mm.

Any particular reason you want an F54/P90 combination?

Cheers, D

No, I'm just after a P90,

I have 2 x L28 engines, ones a F54, the other N42,

neither have a P90 (both have N42) Heads,

I'm after the P90 to turbo it, I've been told the N47 would not be a good combination on a L28 block, but it works good on my L24.

Nigel

Have you thought of using one of your N42 heads?

Valves are heaps easier to get out of USA, both standard & oversize.

If your going to have flat top pistons your compression is going to be far to high to turbo, but with dished standard 280zx turbo pistons it would be good, just cant put over a bar of boost into it. If you build this engine right, you wont need anymore that 10psi max.

I'm building an L28ET motor. F54/P90 combination with just under 9:1 compression I'm expecting about 250RWHP, but over 500Nm of torque on under 10psi and with our cars weighing a miserly 1250 odd kg, that is going to be a handful in anybodies language.

Cheers, D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...