Jump to content
SAU Community

Recommended Posts

hey guys got a really bad shudder in my rs4 drive line shudders under any sort of load any one point me in the direction of any good drive line mechanics to sus this out for me also need cv boots replacing

cheers

Rose

Link to comment
https://www.sau.com.au/forums/topic/341244-driveline-shudder/
Share on other sites

Any kind of mechanic would be good to suss out the problem really.

Possibly a loose bolt, twisted tailshaft, i guess once they are under there, they will know.

Adelaide CV Joint and Mechanical Repairs in Para Hills?

RS4 with the front shaft still in?

Do you have different sized rims or tyres front to rear?

The AWD Stagea requires same diameter/circumference in wheels and tyres combo. If they're not the same, then your altessa system is complaining about it.

:)

  • 3 weeks later...
hey guys got a really bad shudder in my rs4 drive line shudders under any sort of load any one point me in the direction of any good drive line mechanics to sus this out for me also need cv boots replacing

cheers

Rose

I get same issue in my rs4 from time to time. under acceleration some times, bit of a shutter! havent had chance to have a look at it yet! Do have 17x8's on front and 17x9's on rear? no idea if that has anything to do with it! but dont see how having wider wheels would cause a shudder???????

shudder is 99% one of these ..... overheated/worn/bent /oily clutch, worn u-joints/ cv joints or too much lash in tranny or axle , or carrier bearings on drive shafts, (sometimes really worn bushes create shudder feel but rare unless tranny mount or engine mount is broken)easy to suss once the car is jacked up.

could be a combination of a few of the above items,

mine is getting bad, but clutch is worn out....lol annoying for sure

yeah i get that but how can it cause a shudder?

If you have different tyre sizes the transfer case has to slip to make up the difference.

In the R33 and later 4wds there is preload on the clutch inside the transfer case so it doesn't run free like the r32 4wds do. This is why you can not safely just pull a fuse and drive in 2wd with anything later than a R32.

The reason this causes shudder is because the clutches in the transfer case grip until the load between front and rear builds and then slips. This happens over and over very quickly causing a shudder. It can happen anytime, whether under load or not, it just depends at what point the clutch wants to grip/slip.

The shudder can also be caused by air in the system, get it bled out by your mechanic

My car has a shudder under mild load and is caused by air from a leaky bleeder and gasket, it is on the list of things to get fixed.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Wanted to add some of my R33 GTST  R34 GTR wheels, 18x9 ET30 with 255/35/R18 PS4S'   BBS RE-V7 029 18x9.5 ET22 with 255/35/R18 PS4S' Needs a bit of camber   
    • Lamb roast on Saturday will be different 🥲
    • They are under bucket shims. Tomei provides a test shim kit and then any measurement of shim required. 
    • I always wondered how you were supposed to buy a set of 24 buckets and somehow magically have every single one of them yield exactly the desired clearance. I would have thought you'd need to assemble a cam with either 12 "sample" or "example" buckets of known top thickness (or a single such sample/example 12 times over!!) measure clearances at every valve, and then do the usual math to work out what the actual "shimness" of each bucket needed to be, before buying the required buckets to make up he thicknesses that you didn't have on hand.
    • I now seem to be limited in power due to my rev limit/hydraulic lifters in my built RB25. I'm looking into converting over to Tomei solid lifters. Question for anyone that has done the conversion. I was always under the impression that when using the Tomei solid lifter conversion, you would also require new valves (Longer or shorter stems, I can't remember which).  I don't know where I got this idea, as so far I see no mention of this in any of the Tomei documentation. It just states I need the Tomei solid buckets, solid lifter cams and upgraded springs. As my head is already built, all I would need is another set of 1000$ Kelford cams, 500$ buckets and about 4H hours of my time installing and I'm off to the races!?!? There's no way it's that simple, I must be missing something? 
×
×
  • Create New...