Jump to content
SAU Community

Recommended Posts

  • Replies 78
  • Created
  • Last Reply

Top Posters In This Topic

GenesisR32, yep we're in it and another R33 white will be joining me, that's 5 now :cheers:

p.s.

after the mtn run last thursday which i've done a few 360 :headspin: i realized i need new tyres :boobs: , does anyone know where's the best place to get em, like good deals?

springwood crazy clarks sounds good. Like what Nismogirl said, the car park is big and its possibly the best 'neutral' meeting place for both sides.

how about meeting at 8.30pm, have a little social gathering and chit-chat, put names to faces and then finally decide where we all wanna go from there?

each of us will have different suggestions and chances are that we will eventually be split into smaller groups for cruises, mountain runs, home, mistresses :), etc, etc, ... but at least you will still get to choose whatever activities you wanna participate in on your own free will. :)

i got fedrals on my car, they just wore out :) i had 235's though on 18". hard compund and I have to get tyres today as mine ****ed up >=[

I have Khumo 265 35 18"s on the rear, they were about $30 buck dearer than Nankangs.

I've had them since Nov 2002 and they still have heaps of tread!

Got them from Quick Fit at Capalaba.

I might be in this Thursday,.

Agreed, we need somewhere closer to Brisneyland.

As I said, we will only be at the meeting spot to have a chat, then we will probably head home. So don't get cranky at me for organising it and then leaving. Cause people do that quite often when i've said "we are only going to be out for an hour or so"

*scratches head* Yatala is NOT close to the northside. It would be like a 40 minutes drive, and a 10 minutes drive for yous.... I dont really call that fare :S

lol sorry erin, i was doing three things at once when i wrote that...

as said in above post all ideas to mix things up in the name of fairness and fun is great...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...