Jump to content
SAU Community

Recommended Posts

I have recently purchased a rb25 turbo (op6 rear housing) for my rb20. Ive done turbo swaps before and the oil and water feed lines are always a pain in the ass so this time i wanna do it all with braided lines, My question is where can i get a set of braided lines to suit this turbo on my engine?

Any help would be appreciated

Link to comment
https://www.sau.com.au/forums/topic/342289-help-me/
Share on other sites

Search Kinugawa on ebay, hes a reputable seller and has good quality items.

If you go to pirtek or enzed you will need to tell them the sizes etc and it will cost alot.

Kinugawa sells kits on ebay, just make sure you buy the right one. If you have any trouble finding one post back and Ill find it for you on ebay tonight after work.

Link to comment
https://www.sau.com.au/forums/topic/342289-help-me/#findComment-5521893
Share on other sites

Thanks guys, ill check ebay now. Are the fittings on 25 turbos the same thread size an pitch as 20 turbos?

An r31nismoid i thought braided lines were alot better than the factory steel ones, better flowing an less restrictive? Yes ill only be take this turbo off once but there a head f&*k when it comes time to bolt them back up. And i didnt wanna run the risk of crimping the lines when removing/ installing the turbo.

Link to comment
https://www.sau.com.au/forums/topic/342289-help-me/#findComment-5521967
Share on other sites

like nismoid said your better off keeping the factory lines, just replace the brass washers with new ones and away u go. braided lines would be a complete waste of time on a stock turbo. and its actually very easy changing the turbo over..with the right tools

Link to comment
https://www.sau.com.au/forums/topic/342289-help-me/#findComment-5521986
Share on other sites

They are not better flowing or less restrictive. Who said that?

A "X" diameter piece of hose will flow the same whether its braided teflon or steel mate.

What you'll run the risk of, with braided, is potential perish/failure over a few years. There are no pro's to going braided for a daily driver

Link to comment
https://www.sau.com.au/forums/topic/342289-help-me/#findComment-5521990
Share on other sites

I also believe its better to use the stock lines, best bet is to not unbolt them from the turbo when you remove it. That way it simply bolts back on. Remember there are only 2 to contend with lol, the other 2 are the return and one that connects to a rubber hose.

If you must remove the lines then only thread them in loosely until you mount the turbo, then start up the threads on the block and tighten it all up! That will give you some extra flexibility to get the line back in place. Dont worry too much if you bend the lines a little, just do not crimp them.

Link to comment
https://www.sau.com.au/forums/topic/342289-help-me/#findComment-5523238
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...