Jump to content
SAU Community

Recommended Posts

Morning Gentlemen,

Just curious to see what people have in terms of options for changing the Diff ratio, particularly for a 32 gt-r.

Looking to go 4.3 but its a massive pain in the proverbial finding the diffs in the first place and then getting them in good condition..

What have people done ?

Link to comment
https://www.sau.com.au/forums/topic/342377-diff-ratios/
Share on other sites

I'm guessing they are gts-4 diffs ?

I've put them in mine. Took the crown wheel and pinion out of the gts-4 diffs and put them inside my GTR diffs after having them cryo treated for extra strength. Difference is definitely noticeable in 3rd and 4th.

Link to comment
https://www.sau.com.au/forums/topic/342377-diff-ratios/#findComment-5524963
Share on other sites

yeah going rate these days about $1000 for a set. still good value if you ask me. the biggest head f**k is you have to remove the engine to replace front diff so if you're not doing it yourself the labour bill for a simple ratio change quickly becomes a grand or two making it not exactly cheap.

so if you're bothering to put the 4.4 GTS4 gears in your GTR may as well grab a front LSD while you're at it and do the rear nismo LSD clutch pack upgrade too.

so:

$1000 for front and rear GTS4 ratios

$1000-$1600 for front LSD (depending on new or used and what brand)

$300-$350 for set of nismo clutch packs for rear LSD

engine removal and replacement (dunno maybe $1000-$1500)

remove sump and get new lsd and gears fitted and set (maybe $200)

remove rear LSD, fit clutch pack upgrade and CW and pinion (again maybe $200)

makes it an expensive upgrade all round but very nice once it's all done. it will handle like a different car and drive out of corners much improved.

Link to comment
https://www.sau.com.au/forums/topic/342377-diff-ratios/#findComment-5525797
Share on other sites

yeah going rate these days about $1000 for a set. still good value if you ask me. the biggest head f**k is you have to remove the engine to replace front diff so if you're not doing it yourself the labour bill for a simple ratio change quickly becomes a grand or two making it not exactly cheap.

so if you're bothering to put the 4.4 GTS4 gears in your GTR may as well grab a front LSD while you're at it and do the rear nismo LSD clutch pack upgrade too.

so:

$1000 for front and rear GTS4 ratios

$1000-$1600 for front LSD (depending on new or used and what brand)

$300-$350 for set of nismo clutch packs for rear LSD

engine removal and replacement (dunno maybe $1000-$1500)

remove sump and get new lsd and gears fitted and set (maybe $200)

remove rear LSD, fit clutch pack upgrade and CW and pinion (again maybe $200)

makes it an expensive upgrade all round but very nice once it's all done. it will handle like a different car and drive out of corners much improved.

i belive you dont need to remove the engine, well thats straight from terry at award diffs,

he told me ha can do it in the car takes a little longer he said but no problems.

i was going to do it when he was doing my diff swap to the new sump but as i hadnt sourced gears yet he said he can do it later when its in the car.

Link to comment
https://www.sau.com.au/forums/topic/342377-diff-ratios/#findComment-5525809
Share on other sites

yeah I have heard one of two people say they can do it with engine in car but it would be a massive c u next tuesday of a job. getting all the sump bolts out with engine and box still in the car is going to be tough. would still be a fair few hours labour to remove + replace sump even if they can do it with engine in car, and at $800-$100 an hour the labour bills add up quick!

still it's a good mod. worth doing.

Link to comment
https://www.sau.com.au/forums/topic/342377-diff-ratios/#findComment-5525854
Share on other sites

You don't need to remove the sump to do it in the car.

yeah makes sense. I guess once driveshaft is out and diff cover off you can get enough room to get it out. in that case... rock on.

Link to comment
https://www.sau.com.au/forums/topic/342377-diff-ratios/#findComment-5526339
Share on other sites

yeah going rate these days about $1000 for a set. still good value if you ask me. the biggest head f**k is you have to remove the engine to replace front diff so if you're not doing it yourself the labour bill for a simple ratio change quickly becomes a grand or two making it not exactly cheap.

so if you're bothering to put the 4.4 GTS4 gears in your GTR may as well grab a front LSD while you're at it and do the rear nismo LSD clutch pack upgrade too.

so:

$1000 for front and rear GTS4 ratios

$1000-$1600 for front LSD (depending on new or used and what brand)

$300-$350 for set of nismo clutch packs for rear LSD

engine removal and replacement (dunno maybe $1000-$1500)

remove sump and get new lsd and gears fitted and set (maybe $200)

remove rear LSD, fit clutch pack upgrade and CW and pinion (again maybe $200)

makes it an expensive upgrade all round but very nice once it's all done. it will handle like a different car and drive out of corners much improved.

Definitely looking at the 4.4 the car is mostly street driven and will be doing some test and tunes until I feel it is ready for trackdays.

I feel having a huge top speed...260km/h plus Isn't necessary as I won't be pulling that sort of trap speed at Willowbank or QR.

Would definitely like to redo the rear LSD but is the front necessary, particularly on a street car ?

Link to comment
https://www.sau.com.au/forums/topic/342377-diff-ratios/#findComment-5526392
Share on other sites

front lsd not necessary on a street car. but a good idea for a track car. especially if you are changing ratios, may as well do it together. have a look at any serious track GTR... front lsd.

it's not like you'll fail without one, but on the track a front LSD transforms the car. just like a rear LSD does for a GTST etc. needs a fair adjustment in driving style though.

Link to comment
https://www.sau.com.au/forums/topic/342377-diff-ratios/#findComment-5526412
Share on other sites

Why does the sump need to come off for??

There is 3 bolts retaining the NS drive shaft axle, 9 bolts from memory holding the bearing retainer plate in the OS of the diff housing and the flange nut on the pinion shaft.

The center falls out the front, the pinion and shaft also get knocked out the front. A small slide hammer can pop the old bearing cones out easily and a tappered nylon drift can knock the new ones back in.

Bearing preload and backlash is easy to set up with shims.

We used to service the quaife center in my old race car every 6 meetings and inspect the crown wheel/ pinion gears afte every race meet. Never had any problems getting the diff center in and out.

Link to comment
https://www.sau.com.au/forums/topic/342377-diff-ratios/#findComment-5526594
Share on other sites

If there was no backlash adjustment or bearings replaced it took an hour with 2 of us doing it.

If it needed a new crown wheel, pinion or bearings it could take up to 4 hours max depending on how the assembly went.

Typically we were smashing crown wheel and pinion teeth off the start line so we were doing it all the time, never fixed one at the track though, just drove it RWD in most trophy races after it broke in the heats.

That's a car which was constantly apart and we knew it inside out

Link to comment
https://www.sau.com.au/forums/topic/342377-diff-ratios/#findComment-5526824
Share on other sites

it took me 5-6 hour's to do my first 1, which was drive in hoist, CV's out, prop shaft out, pop the diff cover pull the centre,

pop the pinoin, then new bearing's 3 or 4 goes to get the pinoin height right same with back lash..

Take's about half hour less each time, far from a hard job just gotta take your time and you'll knock it out no drama..

Cheers

Link to comment
https://www.sau.com.au/forums/topic/342377-diff-ratios/#findComment-5526869
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • When you crank your car, and hit it with a timing light, can you see a steady crank timing?
    • Oh, forgot to add, A few months ago I was getting mixture codes and the car was using crap loads of fuel. You could smell the unburned fuel in the exhaust, it was crazy strong. Economy was over 17.5 l/100 and usually around 19. I smoked the engine and found a leaky CCV hose which I replaced and then I replaced my two pre cat O2 sensors, I also replaced the MAF. This fixed my mixture codes and improved my exonomy but I'm still 14 - 15 l/100 when pottering about town so something is still amiss. Throttle response is much better and it has more pep but I'd like to know why it's still so thirsty (and I'm hoping that whatever it is gives me a bit more poke).    
    • Car is on factory injectors/z32 maf/ q45 throttle body/ z32 ecu with nistune 
    • Hello all, currently finishing up a rb25 swap into my s14. Having issues with starting, car has spark (confirmed by pulling a plug and watching it spark), has fuel(confirmed by checking pulse/voltage at injectors all spark plugs are soaked in fuel). Car cranks over and pops into the exhaust with a heavy fuel smell but no attempt to start or run, I have torn the timing cover off and triple confirmed timing, turned the CAS in multiple spots both directions, attempted to start with coolant temp and maf unplugged, checked my fuel lines and made sure they weren’t backwards, checked voltage at cas/injectors/coilpacks, made sure all the grounds in the harness are connected and added a few grounding straps (1 from chassis to block, 1 from chassis to head, and 1 from chassis to igniter chip) I am getting stumped here. As a last ditch effort I made a full grounding harness tonight that’s going to run from the battery and add an extra ground from the battery onto the coil pack harness/igniter chip/ intake manifold/ Wiring specialties harness ground/ and alternator. I’m hoping maybe the grounding harness will fix it here but posting here to see if anyone has any other ideas on what else I can check. My fuel pressure is unknown right gauge will be here tomorrow.  IMG_3206.mov
    • yeah I was shocked when I checked my spare OEM on and as below that's how they come from Nissan. (side interesting note new NEO gearbox and replacement park lack the brass bush on the tips and its just all alloy) unsure about damage to the box currently back at 1110 to be pulled down/inspected and selector fork replaced as he built it previously and given the never before seen failure on his billet forks he is replacing it under warranty. He said he has used always OEM the keyway tab without issue for years so it could be an unlucky coincidence. I did talk to him about the sharp corners and stress concentration too. Re: hard shifts i got 7+ years out of the OEM one and the fork itself failed not the keyway. so could be bad luck as I said or an age thing + heat cycles in box and during fabrication of billet?
×
×
  • Create New...