Jump to content
SAU Community

Recommended Posts

Morning Gentlemen,

Just curious to see what people have in terms of options for changing the Diff ratio, particularly for a 32 gt-r.

Looking to go 4.3 but its a massive pain in the proverbial finding the diffs in the first place and then getting them in good condition..

What have people done ?

Link to comment
https://www.sau.com.au/forums/topic/342377-diff-ratios/
Share on other sites

I'm guessing they are gts-4 diffs ?

I've put them in mine. Took the crown wheel and pinion out of the gts-4 diffs and put them inside my GTR diffs after having them cryo treated for extra strength. Difference is definitely noticeable in 3rd and 4th.

Link to comment
https://www.sau.com.au/forums/topic/342377-diff-ratios/#findComment-5524963
Share on other sites

yeah going rate these days about $1000 for a set. still good value if you ask me. the biggest head f**k is you have to remove the engine to replace front diff so if you're not doing it yourself the labour bill for a simple ratio change quickly becomes a grand or two making it not exactly cheap.

so if you're bothering to put the 4.4 GTS4 gears in your GTR may as well grab a front LSD while you're at it and do the rear nismo LSD clutch pack upgrade too.

so:

$1000 for front and rear GTS4 ratios

$1000-$1600 for front LSD (depending on new or used and what brand)

$300-$350 for set of nismo clutch packs for rear LSD

engine removal and replacement (dunno maybe $1000-$1500)

remove sump and get new lsd and gears fitted and set (maybe $200)

remove rear LSD, fit clutch pack upgrade and CW and pinion (again maybe $200)

makes it an expensive upgrade all round but very nice once it's all done. it will handle like a different car and drive out of corners much improved.

Link to comment
https://www.sau.com.au/forums/topic/342377-diff-ratios/#findComment-5525797
Share on other sites

yeah going rate these days about $1000 for a set. still good value if you ask me. the biggest head f**k is you have to remove the engine to replace front diff so if you're not doing it yourself the labour bill for a simple ratio change quickly becomes a grand or two making it not exactly cheap.

so if you're bothering to put the 4.4 GTS4 gears in your GTR may as well grab a front LSD while you're at it and do the rear nismo LSD clutch pack upgrade too.

so:

$1000 for front and rear GTS4 ratios

$1000-$1600 for front LSD (depending on new or used and what brand)

$300-$350 for set of nismo clutch packs for rear LSD

engine removal and replacement (dunno maybe $1000-$1500)

remove sump and get new lsd and gears fitted and set (maybe $200)

remove rear LSD, fit clutch pack upgrade and CW and pinion (again maybe $200)

makes it an expensive upgrade all round but very nice once it's all done. it will handle like a different car and drive out of corners much improved.

i belive you dont need to remove the engine, well thats straight from terry at award diffs,

he told me ha can do it in the car takes a little longer he said but no problems.

i was going to do it when he was doing my diff swap to the new sump but as i hadnt sourced gears yet he said he can do it later when its in the car.

Link to comment
https://www.sau.com.au/forums/topic/342377-diff-ratios/#findComment-5525809
Share on other sites

yeah I have heard one of two people say they can do it with engine in car but it would be a massive c u next tuesday of a job. getting all the sump bolts out with engine and box still in the car is going to be tough. would still be a fair few hours labour to remove + replace sump even if they can do it with engine in car, and at $800-$100 an hour the labour bills add up quick!

still it's a good mod. worth doing.

Link to comment
https://www.sau.com.au/forums/topic/342377-diff-ratios/#findComment-5525854
Share on other sites

You don't need to remove the sump to do it in the car.

yeah makes sense. I guess once driveshaft is out and diff cover off you can get enough room to get it out. in that case... rock on.

Link to comment
https://www.sau.com.au/forums/topic/342377-diff-ratios/#findComment-5526339
Share on other sites

yeah going rate these days about $1000 for a set. still good value if you ask me. the biggest head f**k is you have to remove the engine to replace front diff so if you're not doing it yourself the labour bill for a simple ratio change quickly becomes a grand or two making it not exactly cheap.

so if you're bothering to put the 4.4 GTS4 gears in your GTR may as well grab a front LSD while you're at it and do the rear nismo LSD clutch pack upgrade too.

so:

$1000 for front and rear GTS4 ratios

$1000-$1600 for front LSD (depending on new or used and what brand)

$300-$350 for set of nismo clutch packs for rear LSD

engine removal and replacement (dunno maybe $1000-$1500)

remove sump and get new lsd and gears fitted and set (maybe $200)

remove rear LSD, fit clutch pack upgrade and CW and pinion (again maybe $200)

makes it an expensive upgrade all round but very nice once it's all done. it will handle like a different car and drive out of corners much improved.

Definitely looking at the 4.4 the car is mostly street driven and will be doing some test and tunes until I feel it is ready for trackdays.

I feel having a huge top speed...260km/h plus Isn't necessary as I won't be pulling that sort of trap speed at Willowbank or QR.

Would definitely like to redo the rear LSD but is the front necessary, particularly on a street car ?

Link to comment
https://www.sau.com.au/forums/topic/342377-diff-ratios/#findComment-5526392
Share on other sites

front lsd not necessary on a street car. but a good idea for a track car. especially if you are changing ratios, may as well do it together. have a look at any serious track GTR... front lsd.

it's not like you'll fail without one, but on the track a front LSD transforms the car. just like a rear LSD does for a GTST etc. needs a fair adjustment in driving style though.

Link to comment
https://www.sau.com.au/forums/topic/342377-diff-ratios/#findComment-5526412
Share on other sites

Why does the sump need to come off for??

There is 3 bolts retaining the NS drive shaft axle, 9 bolts from memory holding the bearing retainer plate in the OS of the diff housing and the flange nut on the pinion shaft.

The center falls out the front, the pinion and shaft also get knocked out the front. A small slide hammer can pop the old bearing cones out easily and a tappered nylon drift can knock the new ones back in.

Bearing preload and backlash is easy to set up with shims.

We used to service the quaife center in my old race car every 6 meetings and inspect the crown wheel/ pinion gears afte every race meet. Never had any problems getting the diff center in and out.

Link to comment
https://www.sau.com.au/forums/topic/342377-diff-ratios/#findComment-5526594
Share on other sites

If there was no backlash adjustment or bearings replaced it took an hour with 2 of us doing it.

If it needed a new crown wheel, pinion or bearings it could take up to 4 hours max depending on how the assembly went.

Typically we were smashing crown wheel and pinion teeth off the start line so we were doing it all the time, never fixed one at the track though, just drove it RWD in most trophy races after it broke in the heats.

That's a car which was constantly apart and we knew it inside out

Link to comment
https://www.sau.com.au/forums/topic/342377-diff-ratios/#findComment-5526824
Share on other sites

it took me 5-6 hour's to do my first 1, which was drive in hoist, CV's out, prop shaft out, pop the diff cover pull the centre,

pop the pinoin, then new bearing's 3 or 4 goes to get the pinoin height right same with back lash..

Take's about half hour less each time, far from a hard job just gotta take your time and you'll knock it out no drama..

Cheers

Link to comment
https://www.sau.com.au/forums/topic/342377-diff-ratios/#findComment-5526869
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks for posting, your engine bay looks tops. I'm fairly sure you posted the wrong video though, I think you were supposed to upload the one from your "private test road" where it's banging off the limiter with the gate open?
    • This is something to be careful of. I did a bit of digging on the NM35, as I spend a lot of time on near brand new cars and CANBus related stuff, which uses the same "OBD2" plug for a fair chunk of making my life easy. The NM35, does NOT support OBD2. The data pin is actually on Pin3, which is a manufacturer specific pin, and requires Consult3 to connect to the NM35. Your low voltage, is either because the NM35 doesn't have 12V to the constant power pin on the J1962 (OBD2) connector, OR, it is attempting the standard comms, (CanBus, K Line, etc) and can't see any voltage on those pins. Some people have had success accessing SOME data from the vehicle on OBD2 specification, using a module that supports KPW. My assumption, like Duncan has stated, it will likely actually be JOBD, where there is some cross over with the OBD2 and JOBD standards. Note, lots of "OBD2" dongles, do NOT support KPW, which is what you need for a lot of Japanese vehicles of this era (And even up until recent years!), EG, Subaru, Suzuki, etc.    The end of this thread is probably worth a read, as some people did find a way to get a display up in the NM35 recently, looks like someone implemented all the stuff needed to make it work. (The right protocols).  
    • Depending on the purpose of the car, and how much more fabbing you want to do, and what clearances you have, you could look to raise the motor, which will raise the front diff up. Likely would mean altering the chassis rails etc etc, hence the more fab work you'd need to do. However, this can create issues, not just in clearance with everything fitting under the bonnet, but you've also raised a LOT of weight up in the car, and this will DEFINITELY alter handling characteristics (But, so will how much weight you've already added to the front end). You'll also have to deal with the fact the gearbox to rear diff is now out of alignment too for the tail shaft, and alter the angle of the diff, or deal with a bit of potential vibration. Raising the motor an inch up, is effectively the same as making the whole car sit higher by not lowering it as far. So one inch higher motor, theoretically means you can drop the car an extra inch lower, and maintain the same angles in the CVs. Again, depends on the purpose of the car. If it's a just cruiser on the street car, maybe won't be an issue. If it's meant to be a time attack car, I can see you not wanting to raise the motor. This is just for you to ponder as an idea.
    • Have you not seen geospy.ai? It can now give GPS co ords to within a metre from a photo, even if it's a random photo you take inside. Supposedly at the moment only the government/law enforcement has access to that... Supposedly...
    • I've got the rear ones, they're certainly beefy. I need to take them to my driveshaft guru to check over, he's very fussy about the quality of components so I'll let you know if they are made of cheese by a blind man.   Are you in Australia? A mate just had a set of EN26 shafts made for his K20 Lotus by our fabricator which were quite cheap (compared to Driveshaft Shop) so if you can procure the CV's and draw what you need he'd make them for ~$800 for the pair.
×
×
  • Create New...