Jump to content
SAU Community

Recommended Posts

  • Replies 96
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

http://maps.google.com/maps?f=d&source...mp;t=h&z=10

Full path for those interested, including the meetup point at Albion Park (along the side of the road there like last time)

hey owen. i tagged along the last cruise up to the pie shop.. u guyz gonna meet up at ap maccas again or along side the school??

hey owen. i tagged along the last cruise up to the pie shop.. u guyz gonna meet up at ap maccas again or along side the school??

probably a bit of both; as it gets closer i'll post up a semi-meet at maccas, but predominantly will be at the school. don't want those cops rocking up again :)

probably a bit of both; as it gets closer i'll post up a semi-meet at maccas, but predominantly will be at the school. don't want those cops rocking up again :)

yea true that

Sounds good, anyone from the blacktown area want to meet up at wood croft maccas an hour before hand?

let me know how you go with this. I am in greystanes so if you find yourself alone ill meet ya somewhere close to make the trip down

Rockslide On Macquarie Pass this morning.

It affects westbound (ie uphill) traffic.

Plan B (if roadworks are still ongoing in 2 weeks time) would need to be...

* Continue through Albion Park onto Terry St > Jamberoo Rd (southbound)

* Just before coming into Jamberoo > turn right onto Jamberoo Mountain Rd > Robertson Pie Shop at the top.

If Plan B is implemented, drivers just need to be careful of narrow sections going up through Jamberoo Pass :)

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
    • Bloody apprentices! 🙄
    • Not sure yet.  Was considering speedtek because it was rated to 800hp, but when I did some research about him I don't think I will go for that🤣 So maybe giken gear set, but I'm afraid it won't be strong enough🙄
×
×
  • Create New...