Jump to content
SAU Community

Recommended Posts

Good to hear Chris,Roys a top bloke and he helped me out heaps :D

Where the power wire branches out it's right under the throttle body.

I will also put up my maps maybe even tonight or on the weekend.

One thing I learnt yesterday is check your plenum bolts coz I had one missing and god knows for how long.I put another bolt in and now it spools up so quick like 500rpm quick.I would get 11psi at 4000rpm in second before and now get 11psi at 3500rpm,so much better to drive.

  • Replies 121
  • Created
  • Last Reply

Top Posters In This Topic

Well, on saturday morning ( I had a few hours to kill before going to a wedding LOL!) I had a look at my spare motor to see if I could locate the power wire going to the injectors

As it was a spare, it was all done for a bit of practice, next weekend hopefully I can get it all done

Took me about half a hour to get everything off and I found the wire no probs. On mine I traced it from the injectors back up the loom, and it branced off into four, with one wire going down and branching of to three to feed the foward 3 injectors

I tested my resistor pack, and it measured 6 ohms on each wire, so looks to be good.

How did you guys get the plugs of the injectors? Being a spare motor I tried a few things and the only way I could get them of was by pulling that retaing spring wire thing off but I kept on breaking the little plastic bits off that held that spring in place!! Hopefully there is a better way than what I was doing!

All seemed pretty straight forward though, to get the fuel rail out I had to pull the back two injectors out of the rail, as they would foul on a hose going to the plenum

Another thing, after taking the throttle body and the AAC valve assembly off the gaskets where buggerd, chances are it will happen when I do it to the motor in the car it will tear them too, can I use gasket paper and make some replacemnets up or are gaskets available from Nissan as a spare part?

Other than that, all seems to be not to hard at all

How do my maps I have compare to everyone elses?

Chris

i used a pair of needle nose pliers to remove the injector plug clips...they came off with no hassles...

I replaced my throttle body gasket and aac valve gasket on mine (i had every gasket replaced on my new motor etc.) as every one of em is at least 12 years old....go the Nissan genuine 'cos their cheap, and not worth replacing later if they leak :rofl:

Sorry, worked Saturday, and slept most of Sunady after the drive back to Vic. Ill have a look at the Maps later this week and post up before sat morning, though my map will only be good for up to 2500rpm then our turbo characteristics are likely to be very different

No probs mate, I have ordered my gaskets for the throttle body and AAC valve, they should be in today

I have a feeling that my map is for bigger injectors but I will wait to do a quick comparison first. If you guys don't want to post them up you can PM them to me if you want

When I get my car tuned I will post up the final map for comparison's sake. I punched in all the numbers into a Excel spreadsheet BOOSTD made up, it all looks to be pretty good, with no big holes or dips in the fuel map

Is there a option in the PowerFC to adjust the injector scaling? What I was thinking is if the tune is no good in my car to get me around for a few days before I get it tuned, I could always load the standard map and reduce the overall fuel map by 63% (280 v 440cc injectors, please correct me if I am wrong??) and it should be drivable at least, allthough it wouldn't be seeing any sort of boost before it hits the dyno!!

Chris

Roy has a PowerFC

Got all my gaskets and crap just then, so looks like this weekend I should get it all done. Also picked up a boost control kit for the PFC as well :D

Just need to find out if my maps are suitable now or if they are no good, if not I will do as I said in my previous post and default the PFC and use the injector scaling function to drop back the amount of fuel, either way it should work............

Chris

Ah ok, thanx. I just read the whole post and there was a post from him from Feb saying he's using rb20 ECU. Must've upgraded since then. Would RB26 injectors work on the RB20 ECU or does it need to be re-mapped?

It would need to be re-mapped, as they are a much larger flowing injector

Hey Chris,

this might be a stupid question, what does the pfc value represent, is it load?? or am i confused???

Also on the fuel map, is 136 the largest number u can go (most amount of flow?). This would have to be changed when larger injectors are fitted or is that where injector correction comes into it?

I'm trying to understand how these things work.

Cheers

Hey Chris,  

this might be a stupid question, what does the pfc value represent, is it load?? or am i confused???

Also on the fuel map, is 136 the largest number u can go (most amount of flow?). This would have to be changed when larger injectors are fitted or is that where injector correction comes into it?  

I'm trying to understand how these things work.

Cheers

As far as I can work out - the PFC Value part is refering to the location of the point of the map, from 1-20, so I am pretty sure its load. I didn't come up with the chart, so I cannot be sure, I just punched in my numbers I had copied of my PFC

136 isn't the biggest number you can go, but I am not sure what it goes up to as I haven't played around with it much. The map that was in there before mine was from BOOSTD's R33, which was running standard injectors and had numbers well over 1000 entered in, but I will add that the fuel map looks pretty average to me, but I am no expert

I am trying to find a english manual so I can work out all the functions in the hand controller

Chris

Chris

Looking forward to seeing this result... just went and got me a set of gtr injectors :D

I am going to be taking alot of pictures so in the future if someone wants to do the same it will be pretty straight forward

Don't forget to get the resistor pack!

Chris

so is it right to say that your tune is more for response compared to boostd which was more for top end???? This is what i'm gathering from comparing the two or its not a fair comparison (rb20 vs rb25)????

This is pretty interesting!!

so is it right to say that your tune is more for response compared to boostd which was more for top end???? This is what i'm gathering from comparing the two or its not a fair comparison (rb20 vs rb25)????

This is pretty interesting!!

I have no idea whats mines tuned for, I plugged it in, it started, I turned it off.

I copied the maps from it and that was it, my car is currently running on the stock (chipped) ecu

It will be interesting to compare it with what Roy and R31POWER's maps are like, especially the differant fuel maps

Chris

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I have been being VERY quiet about what you're alluding to, as it is something that ticks me off... The number of cars from factory that run coil overs is HUGE! Most of them these days do... The other part that annoys me, is people saying "Well all the incabin adjustable suspension is illegal by blah blah blah"... If that's the case, then why can I buy a car brand new that can do it if, FULL STOP in cabin adjustable suspension is illegal...   Also, I could just chuck some aftermarket shocks in my car, throw the stock springs on, after my blue slip, dump my super low springs back in. Same shock and spring style setup... Hell, they could also be the same colour springs etc.     I'm voting, BlueSlipper didn't want to touch the above car for some reason. Whether it be some sort of bias against the car, the owner, them maybe having previously done dodgy shit and now they're being super careful in case they get slapped in the face by the Gumbyment again... Find a new blueslip place.   And can confirm as you had said, yes there are holy bibles of vehicle heights, and all sorts of other suspension stuff. Heck your run of the mill mechanic, and tyre shop has access to all of that stuff. It's how they do wheel alignments...
    • Funny story Heading to Sydney this morning on the HWY there was some slow traffic, so I gave it the beans and midway through my overtaking "power run" I lost all power It seems that I missed a hose clamp,  and the MAF and filter went WiFi To make this more problematic, the little tool kit that lives in the boot, is sitting in the sun room at Goulburn......LOL Luckily for me I found a bit of steel on the side of the road that could be used like a rusty and bent flat head screw driver to tighten it up enough that it got me into Sydney, it is now all tight like a tiger with the aid of a 8mm socket Note to self: Use my brain and double check stuff, and always keep that little tool kit in the car for when I have a brain fart
    • Oh, and as for everyone with their fuel economy changes, I switch between E10 and 98 in the company car. Even do when I had personal cars that could run on E10. You know what changed my fuel economy in any noticeable way? How I drove, and where I drove. Otherwise, say on full tanks of just back and forth from work only (So same trips, same sort of traffic), couldn't notice a difference that I can correlate to the type of fuel in use. In the current vehicle, that's over 42L of USABLE fuel. While 98 is all "more energy dense", it also has higher knock resistance as it takes more energy to get it to ignite too. The longer hydrocarbons, typically more tightly bound. So running the same ignition map, can also produce less power, if there isn't enough time to get it all burnt through properly, as yep, the flame propagation speed is different from lower octane fuel to higher (Higher has a lower flame propagation, due to the more tightly bound and harder to self ignite funs. This is also typically where, a vehicle that is designed purely to run on 91 (Whether it be E10 or normal 91) usually sees absolutely no real world difference in fuel economy for the normal man, woman, or dog.
    • We've got some servos around me that have 91 with E10, 91 (no E10), 95, and 98. At those stations the change from 91 E10 to 91, is typically around 8c/L.   But lets not get started on the price of fuel in Oz. It's ridiculous. All the service stations around me, bar one, the price of fuel has been over the $2 mark per litre for the cheapest, 98 being around $2.45. That one service station is a CostCo, fuel from it comes from the same refineries, and makes no pitstops, it runs great, including the 98. In fact, I've had no issues on CostCo fuel, but plenty of issues at other stations!. The CostCo fuel, was $1.65 roughly this week for 94 with E10. $1.88 for 98. Servos directly across from it, $2.10 for 91 E10, and $2.48 for 98. The part I had to laugh at? If I drive multiple HOURS away from Brisbane, say out near Nanango, or Kingaroy, or even out to Goondiwindi, the price of their fuel, is the same as what it is at the CostCo... Oh, and that BP servo at Goondiwindi is HUGE and goes through epic turnover of fuel, so it's not sitting there for weeks going to shit. And what blows me away, my mate is one of the people who drives the Fuel Tanker all around QLD, delivering to all those places. At the same company his previous role was doing the "local haul" deliveries... Same truck, same driver, same pickup point it all comes from. So you tell me, how the hell it is 60c/L CHEAPER for fuel, when nearly all else is equal, except they require a B-Double to drive half a day out of Brisbane, and half a day back, every second day, compared to the delivery that can be under 30 minutes drive from the fuel pickup point... Not to mention, go five blocks down the road, and Ampol to Ampol will vary 30c/L... And I've had this conversation with my mate... The way it's priced, is just typical, pure and utter rubbish... He also does runs from Brisbane, to all over QLD, down to Newcastle, Sydney, Nowra, Melbourne, Geelong, and even out to parts of the NT depending on the companies needs. His main stuff is all the longer distance away from home for a few days at a time, then when he's back, he loves to just pickup extra shifts wherever he can in whichever truck, hence all the weird different places.   Oh, as for getting E10 into all the fuels in Australia... It was very quickly highlighted, that we don't have enough biomass available to use to make E10 sustainably like they require, and it would dramatically cut into our, and the worlds food chain supply...   I vote we all just start running on liquid methane gas... Plenty of that just getting tapped off at tips from underground decay... (Note, this is pure just stupid commenting. I could very easily highlight the reasons its not a good idea especially on scale...)
    • Am I correct in assuming that the R35's are getting the classic skyline haircut off the odometer?  Quick search on carsales, there are 33 08 and 09 GTR's for sale, only 2 of them have more then 100,000km's on them (116,075 and 110,000 respectively).  And somehow there are about 25 for sale with around 60,000kms? Looks like the classic skyline haircut to me =/
×
×
  • Create New...