Jump to content
SAU Community

Help! Break Line Needed!

Andrew.Y

By Andrew.Y,
in Victoria

 Share

Recommended Posts

Andrew.Y Enthusiast

Andrew.Y

Posted
Posted

hey there I'm doing my R34 GTR complience and I need to find rubber breaklines with serial numbers on it. I have tried a couple of places I know to get it made but they have all stopped making them.

Now I am stuck with it which I can't get it on road. Is there a place in melbourne that still makes break lines for R34 GTR?

Much appriciated!

Andrew

Link to comment
https://www.sau.com.au/forums/topic/343498-help-break-line-needed/
Share on other sites
blind_elk Grand Master

blind_elk

Posted
Posted

Or you could try Maltech in Geelong. They have ADR approved braided lines (not sure if for the 34 though).

http://www.maltech.com.au

Postal Address: 125 Andersons Rd, Drysdale, VIC 3222

Phone: 0418 378 939

Fax: (03) 5251 1790

Email: sales@maltech.com.au

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • PranK
      Hiya!

      By PranK · Posted

      You're now in the unrestricted member group so upload away! 
    • MBS206
      Rear subframe stay bracket bolt removal issues

      By MBS206 · Posted

      TBH, it sounds like the threads on the bolt are fubar in a specific section. Most likely as you've been working it back and forth it has torn threads out, as you loosen the bolt, this section enters the nut, now you're spinning a round shaft inside the nut, there's no threads here.   Use something similar to a claw on a hammer that will fit either side of the bolt head and try to apply downward force while also undoing it. The idea is to attempt to catch a thread, or just rip the f**ker out. Caution on ripping out, as it could bend/maime/mangle what the captive nut attaches to. If the captive nut is actually okay, you could do the dirty part of cutting the head off the bolt, then cut a slit in the end of the thread that's now exposed and then screw it up and into the area the captive nut is until it falls out the other side. However, this does risk the remainder of the bolt rusting over time and damaging near the captive nut and also making it rust. However, so can cutting pieces of panel work out to access this area if you don't reseal it properly.
    • MBS206
      Rb25 det nitto washer crank gear

      By MBS206 · Posted

      Well, every piece of information on that part when you track it back to Nitto says it's for a KIT of theirs. It is also designed thicker to be stronger. And they speak about a specific harmonic balancer bolt they supply for the whole setup.
    • MrStabby
      Rear subframe stay bracket bolt removal issues

      By MrStabby · Posted

      Techniques for removing stuck bolts are: hitting the bolt head with a hammer, heating the bolt to red hot then letting it cool and working it back and forth like you are already doing. AFAIK the idea is to try to crush whatever material is stuck between the threads (and heat also melts locktite but that's almost certainly not relevant in this case).
    • GTSBoy
      Rb25 det nitto washer crank gear

      By GTSBoy · Posted

      Yuh, I think it works with the Nitto gear only. I presume that you're not also using the Nitto gear? Watch the video. Compare the interface between the Nitto gear and washer (on the gear side) vs the stocker and decide if you think the Nitto gear is different from stock there.
×
×
  • Create New...