Jump to content
SAU Community

Recommended Posts

Guys i've been trying for 3 days getting the HICAS system off for the replacement of the ISC HICAS lock bar. I've managed to crack one side of the tie rods (with the square nut) and the other one is damn impossible. I've tried using a spanner to hold down the flat parts of the little metal rod inside the HICAS but it's not strong enough and i'm slowly rounding it. Anyone got tips and tricks to share please?

Edited by TyresBro
Link to comment
https://www.sau.com.au/forums/topic/345000-damn-hicas-bar/
Share on other sites

Try grab one side with bench grip or something. That would be easier. When I was doing mine I didn't have the bench grip so I pulled the whole thing

out with the help of my brother hold the steering rack on the ground, use a big shifter and him holding the shifter in place, and kick the shifter really hard :). The impact would make it easier to crack.

Hope this helps, where about are you in SE ?

Link to comment
https://www.sau.com.au/forums/topic/345000-damn-hicas-bar/#findComment-5559467
Share on other sites

Hey mate thanks for being the first to reply. I'm located in Dandenong area. Very close to giving up :) it's taking all my time.

I've tried those metal vice grips ( http://vetquip.com/products/Orthopaedic%20...Grip%2020cm.gif ) + a spanner to hold it in place since it's kinda rounded off. Too slippery as well. The HICAS unit has been remounted with the 2 bolts so i didn't need to hold it.

When people say shifter, does that mean a spanner?

Edited by TyresBro
Link to comment
https://www.sau.com.au/forums/topic/345000-damn-hicas-bar/#findComment-5559628
Share on other sites

Shifter means the adjustable open end spanner, I can come and give you a hand if you need, just pm me :)

I remember disconnecting those tie rod was doing my head in as well... you are not alone !

I live in Noble Park. Not that far away from you.

Edited by Panko
Link to comment
https://www.sau.com.au/forums/topic/345000-damn-hicas-bar/#findComment-5559694
Share on other sites

boostn1099: tried WD40 (RP7 to be exact). Didn't need breaker bar to crack the first one so I don't think it's necessary. I still bit the dust lol.

Panko: Sure bro, when are you usually free? This won't go unrewarded. Also yeah i've been using 2 shifters then...trying...

Edited by TyresBro
Link to comment
https://www.sau.com.au/forums/topic/345000-damn-hicas-bar/#findComment-5559704
Share on other sites

If you get a good enough grip on the nut with the tool, you can then use a low scissor jack to push/move the tool to break the probably rusted/seized contact/threads of the bolt. Or a breaker bar/bar extension etc but i would prefer using the scissor jack to move the tool as it will have alot more control - you are under a car after all. Have fun

Edit - and wd40 that sucker like mentioned above.

Edited by Touge Kyousou
Link to comment
https://www.sau.com.au/forums/topic/345000-damn-hicas-bar/#findComment-5563755
Share on other sites

i remember doing mine, and they were a bitch too.

as long as the hicas is still bolted in place, just get a nice tight spanner onto the nut (or vice grips if the nut is fcked), and then tap the spanner with a hammer in the direction you need to loosen it. The shock from the hit (maybe a few hits) usually helps crack the seal. it worked for me.

and remember this when you're doing your camber arms :blink: you'll need it!

oh yeah, and wd40!! as mentioned above

Edited by Munkyb0y
Link to comment
https://www.sau.com.au/forums/topic/345000-damn-hicas-bar/#findComment-5563804
Share on other sites

a tool worth trying would be a stilson. plumbers use them. as you push on the handle it tightens the grip of it. they are a bit bulky though so you need a bit of room around the bolt/nut in question. i have found them handy in the past.

stilson:

stilson_wrench_36.jpg

Link to comment
https://www.sau.com.au/forums/topic/345000-damn-hicas-bar/#findComment-5565531
Share on other sites

The thing is i'm not having troubles with loosening the bolt, i'm having trouble with the darn grip on the bolt. Have tried the spanner and hammer a few times but the whole unit just keeps turning guess i'll try some more. Will also try the stilson, thanks guys much appreciated.

Link to comment
https://www.sau.com.au/forums/topic/345000-damn-hicas-bar/#findComment-5567051
Share on other sites

  • 2 weeks later...

Guys sorry it's me again. Tried using stilsons, can't get a proper grip on the mildly rounded nut as there isn't enough surface area. Tried hammering the 4 sided nut, both by itself, and tightening the loosened nut and trying. Still can't get it loose. Don't know how you guys make it sound so easy. Called up R E Customs and they wanted $160 to remove the HICAS even though I had the bar already :thanks: I've tried so long already, it wouldn't be worth it if I had to pay that in the end...

This is becoming SOS. Please help.

Edited by TyresBro
Link to comment
https://www.sau.com.au/forums/topic/345000-damn-hicas-bar/#findComment-5579531
Share on other sites

If you have the space you can get a blow torch and heat the bolt up from the thread and try to remove it have done this a ton of times at work and works 99%of the time. if that doesn't work try welding a bolt onto the nut so you can hit the bolt welded to the nut with a hammer but once again only if you have enough room to do so . if you can weld a bolt to the nut be careful not to fuse the nut to the bolt that your trying to remove said nut from. hope any of this helps

Link to comment
https://www.sau.com.au/forums/topic/345000-damn-hicas-bar/#findComment-5579759
Share on other sites

Thing is I don't have any of those equipments let alone experience with them. I saw a post from a forum member who had welded a blob on the other side with the tie rod removed to get a proper grip on the damn thing. I would if I could...

Link to comment
https://www.sau.com.au/forums/topic/345000-damn-hicas-bar/#findComment-5579798
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...