Jump to content
SAU Community

Recommended Posts

Hi there,

My car is an R33.

I've looked but I cannot find any info.

I noticed the other day that when I flicked on the air con a red light came up on the right hand side of the dash. It had what looks like heat waves coming off a pipe like figure.

It only comes on when I turn the air con on. When I turn it off it disappears. Is it somethin to worry about? I wondered if it was some kind of exhaust sensor that has been disconnected when I had my 3" put in.

cheers,

Dan

Link to comment
https://www.sau.com.au/forums/topic/345789-red-light-on-dash/
Share on other sites

Sounds like the catalytic converter temperature warning light, PowerFC use it to indiciate engine knocking

Oh ok, would make sense because I took out the cat... being from NZ.

power fc uses the check engine light to indicate knock by flashing it several times in a short space of time

if its the cat convertor overheat warning then there may be a wiring issue or maybe it was just unplugged when something was done/replaced

power fc uses the check engine light to indicate knock by flashing it several times in a short space of time

if its the cat convertor overheat warning then there may be a wiring issue or maybe it was just unplugged when something was done/replaced

The light will come steady on and maybe flick off for a bit after a while, and then turn on again. I have a Z32 computer installed not a powerfc.

Yeah that's fine was just correcting the previous post.

That's a bit strange. The sensor should bring up a warning (that red light) when excessive temperature is noted in the cat. Sometimes this happens with a stock exhaust when the car dumps fuel into the engine at higher then normal boost levels. But since yours has a 3 inch exhaust I wouldn't think so

Sounds more like a wiring problem, or perhaps the sensor is old and as the wires heat up it's creating to much resistance, but again that doesn't explain why it's only doing it when you turn the air con on. Unless your z32 ecu is throwing to much fuel in when the air con is on, perhaps putting it into a rich and retard mode, I'm not sure.

Does the car drive ok when the ac is on and it does this? Maybe just check the sensor and wiring under the car just as a start. But it doesn't sound like anything to be concerned about

Yeah that's fine was just correcting the previous post.

That's a bit strange. The sensor should bring up a warning (that red light) when excessive temperature is noted in the cat. Sometimes this happens with a stock exhaust when the car dumps fuel into the engine at higher then normal boost levels. But since yours has a 3 inch exhaust I wouldn't think so

Sounds more like a wiring problem, or perhaps the sensor is old and as the wires heat up it's creating to much resistance, but again that doesn't explain why it's only doing it when you turn the air con on. Unless your z32 ecu is throwing to much fuel in when the air con is on, perhaps putting it into a rich and retard mode, I'm not sure.

Does the car drive ok when the ac is on and it does this? Maybe just check the sensor and wiring under the car just as a start. But it doesn't sound like anything to be concerned about

Hey thanks for the reply.

I will be seeing my tuner this weekend for other reasons, but I can check it out with him to see if it is the result of his tune. The car drove fine when i had it on A/C but I never really left it on for a long period once I had noticed it.

I don't even have a cat anymore so I would say that is nothing important also. It is just weird with the air con turning.

cheers,

Dan

probably just a wiring fault then. Might just be earthing the wire for the cat sensor when the AC compressor is cutting in and out or something. Just check to see what they did to the sensor when they replaced your exhaust

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
×
×
  • Create New...