Jump to content
SAU Community

Recommended Posts

HAHAHAHHAHA, Now I know you have nfi about tuning, Methanol cars need to be fkn rich to make power.

running lean or even Gasoline AFR's on methanol will make less power than Unleaded, might not ping, but wont make any power.

lets just get back on track

-but if u ask me we re doing it and ur reading it......................

and cars still runing fine!

  • Replies 121
  • Created
  • Last Reply

Top Posters In This Topic

  • 1 month later...

been making 430rwhp out of a stock internaled rb25 for over 2 years now.

car is thrashed regularly, and sees drift days, circuit days, hill runs and has done 1 boring ass drag day.

car ran @ 12.9 @ 119mph with full drift setup as drag racing just not worth altering the car for

figure has been made on multiple dyno's including hub and roller.

car makes full boost by 3400...

what turbo are you using?

  • 9 months later...

mid 400 s

here s the link to it at 440s

this is a 26 the 25 was sold

here s it at 485 rosting

571 with alittle traction problem

im pretty sure its in the 600s the piping pop off on this run

i think the power is good for now

we will test it and update

camero hooks, we lost about 6 cars (second and third gear doesn t have too much traction)

update before we sold the 25 it was almost 500whp

So we proof it to be reliable in the high 400s

It did 11.1@124

So you had it for 9 months???

5+years would be reliable in my book

9 months and a few runs down the strip doesn't mean much

update before we sold the 25 it was almost 500whp

So we proof it to be reliable in the high 400s

It did 11.1@124

With 480rwhp I ran 132.5mph... Your set up isn't special, it's not even that great and your dyno reads high :whistling:

With 480rwhp I ran 132.5mph... Your set up isn't special, it's not even that great and your dyno reads high :whistling:

Didn't you pull a low eleven? Ima head down the strip when I get my clutch sorted and get me some proof. I am hoping to get kicked out too.

And I am agreeing

And bringing more informationz!

And Ye... :mellow:

I must have taken the I'm with stupid the wrong way... Carry on :)

I think it was a very high 10 which is why he got kicked out.

It's in my signature guys... I mean come on :whistling:

With 480rwhp I ran 132.5mph... Your set up isn't special, it's not even that great and your dyno reads high :whistling:

simonR32

i just saw your built up thread (good job...)

thats what we were looking for someone that did it !!!

so your motor is stock right? and what was the highest power you made? also converted to whp

thanks

we ill see how the stock rb26 does at high 500whp than i post... to compare

Edited by Revspeed

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...