Jump to content
SAU Community

Os Giken R34 Gearbox Rb25

Waldo
 Share

Recommended Posts

Waldo Proficient

Waldo

Posted
Posted

OS Giken 5 Speed Box R34 RB25

Custom order, ratio's setup for a drag car. Recommended use with 4.3 final ratio.

Has about 10 000km's on it, comes with shifter bent forward to suit S13/4/5.

I can supply with SR bellhousing welded on for another $750

IMG_1575.jpg

Ratio's are

2.516 1-speed

1.703 2-speed

1.236 3-speed

1.1 4-speed

0.870 5-speed

$4000

0401 151 011 or PM for contact. I can post anywhere is Aus at your own cost.

Link to comment
https://www.sau.com.au/forums/topic/346264-os-giken-r34-gearbox-rb25/
Share on other sites
GUN_METAL_GTR32 Grand Master

GUN_METAL_GTR32

Posted
Posted

hay buddy

is this the full gear box or just the gear set.

is it the 1-3 or 1-5

does it come with input shaft

can u convert the shifter back to r34 spec

thanks

julz

Waldo Proficient

Waldo

Posted
  • Author
Posted
hay buddy

is this the full gear box or just the gear set.

is it the 1-3 or 1-5

does it come with input shaft

can u convert the shifter back to r34 spec

thanks

julz

its complete, was just taken apart for inspection.

its 1-5.

the shifter looks like its been heated up and bent near the base, it wouldn't be hard to straighten it.

  • 1 month later...
  • 2 weeks later...
Waldo Proficient

Waldo

Posted
  • Author
Posted

this is taken off otomoto website

5-speed $4960 includes strengthened input shaft

The gears in this kit are rated for 1200hp, however due to the limitations of the Nissan synchros above 9000rpm, it is generally best suited to applications up to 800hp

jet64u Contributor

jet64u

Posted
Posted

keen mate but gotta see if i can get my hks triple plate back, got rid of it to go auto will contact u a soon as i know, not interested in swaping for a dirt bike? just thought i'd ask

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      What accelerator cable can be used with greddy plenum

      By Duncan · Posted

      I was 99% sure the standard one is long enough to get there, you might just have to change the throttle orientation. If not, I remember someone having used an r31 cable instead, but that is probably harder to find than r33 by now...
    • V36
      What accelerator cable can be used with greddy plenum

      By V36 · Posted

      HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
×
×
  • Create New...