Jump to content
SAU Community

R32 Gtst Hsd Hr Coilovers, Stock Airbox, Headlights, Pod Filter

turbro123
 Share

Recommended Posts

turbro123 Explorer

turbro123

Posted
Posted (edited)

HSD HR coilovers. Used for less than 500kms, like brand new and in perfect working order, only selling due to change of plans.

6/8 kg springs with a spare set of 4kg springs. Height adjustable and 15 step damper adjustable. $RRP 1599 http://www.hsdcoilovers.com/

$1100

R32 GTST Factory Foglights. Very rare and hard to find, completely intact with no damage and everything included to mount to your car including brackets and wiring. $150

R32 GTST Projector Headlights. Driver side is damaged as can be seen from pictures however still works and there is no damage to mounting points. Passenger side is perfect. $150

R32 GTST factory corner indicators. Good condition, driver side mount was damaged and fixed, glued together then sticky tape was used to hold it in place. Still mount fine and prob doesnt even need tape $80

Side repeaters. Look to be aftermarket but im not sure. $30

R32 GTST factory airbox with snorkle. Good condition, great for returning your car back to stock or clearing defects. $150

3" Pod filter. Good condition. $50

Pick up available from Hornsby in sydney or i can post them. Contact me on 0433 998 250

p1010041wh.jpg

p1010040a.jpg

p1010039a.jpg

p1010037b.jpg

p10100360.jpg

p1010035pk.jpg

p1010033sq.jpg

p1010029q.jpg

p1010028l.jpg

p10100270.jpg

p1010026dv.jpg

p1010025o.jpg

p1010024u.jpg

p1010023j0.jpg

p1010022en.jpg

p1010020e.jpg

Edited by turbro123

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • djr81
      R32 update from 1990's spec.

      By djr81 · Posted

      So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • djr81
      RB26DETT Sketchy boost mod?

      By djr81 · Posted

      Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...