Jump to content
SAU Community

Recommended Posts

as topic says, looking for a place to buy my rb26dett front cut from, more than likely going to go with Just Jap at this stage, seam to be a really good deal and is only about 5 hours from where i live.

i know forum rules are that you cant badmouth or activelly promote your own buisness but there is nothing againts sending me a PM if you have had a horror story from an import yard, or if you have had a great experiance and would recommend again.

Also anything that i should particularly be aware of? i allready have a full timing kit, water pump and N1 oil pump ordered, and im purchasing motor without turbo as im going to run a single.

Cheers

Link to comment
https://www.sau.com.au/forums/topic/346689-best-place-to-buy-frontcuts-from/
Share on other sites

who ever you buy it from dont tell them if you are putting bigger turbo's or aftermarket anything on it or your warranty will be void.

just tell them you need it as a stock replacement for your GTR.

as topic says, looking for a place to buy my rb26dett front cut from, more than likely going to go with Just Jap at this stage, seam to be a really good deal and is only about 5 hours from where i live.

i know forum rules are that you cant badmouth or activelly promote your own buisness but there is nothing againts sending me a PM if you have had a horror story from an import yard, or if you have had a great experiance and would recommend again.

Also anything that i should particularly be aware of? i allready have a full timing kit, water pump and N1 oil pump ordered, and im purchasing motor without turbo as im going to run a single.

Cheers

5 hrs away where do you live, try sss at girraween they usally have 26s instock and if you have problem with engine they will swap it, most of there engines they drive in japan for them selfs to see if there stuffed, remember cheaper isn,t always cheaper

as topic says, looking for a place to buy my rb26dett front cut from, more than likely going to go with Just Jap at this stage, seam to be a really good deal and is only about 5 hours from where i live.

i know forum rules are that you cant badmouth or activelly promote your own buisness but there is nothing againts sending me a PM if you have had a horror story from an import yard, or if you have had a great experiance and would recommend again.

Also anything that i should particularly be aware of? i allready have a full timing kit, water pump and N1 oil pump ordered, and im purchasing motor without turbo as im going to run a single.

Cheers

im asuming your in wa. i used kyp in welshpool they were great they did a compression test for me and also started it up for me. speak to ben if you go there he doesnt do it for the money he does it for the love of cars

i know forum rules are that you cant badmouth or activelly promote your own buisness but there is nothing againts sending me a PM if you have had a horror story from an import yard, or if you have had a great experiance and would recommend again.

i don't think too many people are going to get on here and bad mouth there own business...haha

i've gotten a few motors off SSS and always found them to be pretty good, but as you say they have no good 26's... i've bought a bit of gear of just jap and always found them to be pretty good.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...