Jump to content
SAU Community

Recommended Posts

i bought a new foam for mine and will wash the old one if i can be bothered....

i have heard warm soapy water or kerosene does the job, and not to use harsher chemicals...and u must remember to re-oil it using correct oil, but be very careful not to over oil it as it can ruin the internals of you AFM, which will have adverse effect on how your car runs...

if you do a search you will find more detailed answers.

well u oil the foam after you wash and dry it thoroughly....as i said if u oil it too much you will have problems....

if u arent feeling too confident with this process, you can always buy an new foam which is already oiled for you....it is around 60 bucks so not too bad, and you can rest assure your AFM wont be drowning in oil..:)

Guest RedLineGTR
Guest RedLineGTR

1. U can clean it dish detergent or something similar. Gets all the grease off etc.

2. Use K&N Filter oil or anyother branded filter oil, spray a very light mist over the filter nothing to crazy very light, thats how foam filters come from the factory very lightly oiled which u may sometimes notice. My 2 Cents.

I just bought some oil filter cleaner from autobarn, it looks and smells exacly like detergent so i probably got ripped off. it was $20 for 1 litre, meant to use 50-100ml each time you clean the filter but mine was looking pretty dirty so i used about 300ml. I got a bit carried away but i guessed the element probably hadnt been cleaned since being put on the car years ago in japan.

Air filter oil can be bought from autobarn or wherever.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...