Jump to content
SAU Community

Recommended Posts

Hi,

I have recently fitted a Turboetech Boost controller to my car, and after winding the boost up to 9 PSI, the car now has a bad flatspot on acceleration between 4000 and 6000RPM, after 6000 it Revs past it, and seems to be fine. Between 4-6, its not like its missing, but just generally lacking power, like it can't breathe or something - but will rev past it in all gears.

Initally when I installed it, the car started missing badly, so I gapped the plugs to 0.8MM, and siliconed up the coils. The missing got a lot better, but I thought the flatspot was the same problem. I ordered and fitted spkitfire coils today, but the car still has the flatspot. It seems to mainly be when the car makes full boost - after 6000RPM it tapers off to about 8.5PSI and the fault seems to clear and car accelerates better - can feel the shove after 6000 - not sure if boost tapering is just a coincidence....

I have also tried an ECU reset, and have driven the car while watching readouts in OBD Scantech, nothing really stoodout as being massively wrong. There were no faults logged either. Also had quick check for boost leaks, none visible.

A couple of things I have seen on forums is checking ignition timing, or possible turbo breathing issues. I would have thought at this boost turbo would not be an issue. As for ignition timing - what should it be? Can probably check timing tomorrow arvo.

Anyone have any suggestions, or similar issues that have been resolved? Let me know if any more info is needed..I took a log using OBD Scantech, from about 2500RPM in third all the way to redline, as per zip file below Boost was max 9.2 PSI in this run

Thanks, Russel

.

Full list of mods/history

Car is 1993 series 1 R33 GTST

FMIC

Splitfire Coils

GFB StealthFX BOV

Cat-back 3in Exhaust

New plugs/fuel filter/all fluids

test run, third gear.zip

Link to comment
https://www.sau.com.au/forums/topic/348144-flat-spot-4-6000rpm/
Share on other sites

ECU, if standard may be the problem. TBH a good dyno print out could help, along with a good tuner to help diagnose the problem. May cost dollars but who cares, or wait for more people to comment! Come on mad082, I know your lurking some where!

EDIT: BOV may also be a problem, how was it before BOV?

Edited by Shazza24

Just watched the log file, had only seen live....it appears R&R is spot on, at about 4200RPM it drops timing back to 12 deg, at almost exactly 6000RPM it goes straight to 20deg, and works up to about 25 or so after that. So painful that its doing it at such low boost :(

Thanks for the help.

Edited by Pope

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...