Jump to content
SAU Community

Automatic R33 Box Problems


Recommended Posts

Hey guys just got a problem with my R33 the auto box it doesn't shift into 4th gear just keeps in third e.g high way driving to get to 100km/h it revs to 4.5k is there some plug that may have come loose or something in the engine bay or the any help would be great

Cheers

CHi

Link to comment
Share on other sites

there are a set of 4 looms at the front of the engine bay, under the battery. disconnect all 4, clean them with contact cleaner and try close up the wire clamp things inside the looms so they close tighter when you plug them back in. you'll know what im taking about when you see them.

that should fix your problem.

Link to comment
Share on other sites

ok security the battery is in the boot for the R33 mmmmm and also when over drive is engaged nothing happens even when it is disengaged? like it doesn't shift to third or fourth it stays in second ? so is there any plugs etc i have to check?

Cheers

Chi

Link to comment
Share on other sites

Hey security i've already sprayed contact cleaner and made sure the connections are tighter at those four plugs/loom but still nothing :/ but however i found two plugs at the front near the head lights/radiator which wasn't conencted to anything so any ideas heres a picture of the plugs

post-27271-0-38298300-1294391756_thumb.jpg

cheers

chi

Link to comment
Share on other sites

yeah that will happen.

if the oil is low it will create heat as well as drop the oil pressure inside the box. the auto's gear changes relies on the oil pressure.

change your oil and see where that gets you. you may as well drop the sump off and clean the filter as well.

Link to comment
Share on other sites

  • 8 years later...

bringing up a pretty old thread here but was curious if this issue ended up getting resolved?

may not be able to get an answer, just noticed half of the members that responded and created the post having been on here for quite a few years.

Edited by bazr33
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • You won't make it out of your driveway. Both your rear wheels will go in whichever direction they feel. Your Hicas rack or a lockout bar is required to keep your wheels straight. 
    • Updating results.  Using ATR45SS-0 model VS UHF57-900. Those two are very different turbos, different wheels sets with different wheel hub profiles but yet with almost identical result. I’m intrigued with both turbos performance. ATR45SS-0 was a 61mm turbo first developed in May 2020, UHF57-900 was a 62mm turbo developed in March 2024 as a powered up alternative of a G30-900. On paper ATR45SS-0 maxed at 563rwkws, while UHF57-900 maxed at 568rwkws. ATR45SS was slightly more responsive with slightly better power band through the mid range.  Road driving ability, ATR45SS-0 had better throttle response, felt more robust under throttle, as it wakes up earlier. I think G series wheel hub design made it to have higher inertia under light throttle. Doing bit more prototype work in the next few weeks, will update result when its back on dyno again. ATR45SS0 Blue, UHF57-900 Red Chequered tuner's Dynapack hub dyno, E85 fuel. Mod list is in video below video_20240604_114214.mp4    
    • Did you run the power cables for the mac valve to the other side of the car near the fusebox? Utilizing the stock boost controller cables? or did you run new ones?
    • Hey I have a potentially stupid HICAS question 🤣 I'm currently doing a full hicas delete, Power steering pump modified to non hicas, all lines removed from the car along with all electronics. My stupid question is - Do I need a lock out bar? is there any reason why I cant just remove everything from the rear end? I already have a lock out bar but thinking to save a few extra grams I could also get rid of the arms and tie rods as well and just run it with nothing in its place? or would it have a negative effect on handling?
    • Hi how are you guys?  I know i have been absent for years but im coming back slowly guys just wondering if anyone know where the ball joint on the NISMO arm front and rear can be replaced with OE parts?  Also  i know this is not the thread looking for springs and blistein shocks for the 260rs. Please advcie     cheers    yudy
×
×
  • Create New...