Jump to content
SAU Community

Recommended Posts

the ones on the car arent for sale thats why :thumbsup:

i have both of the headlights that are listed for sale still though.

  • Replies 113
  • Created
  • Last Reply

Top Posters In This Topic

hi, yes i do have the front seatbelts.

Driveshafts

Rear brakes + hubs and knuckle

back section of handbrake cable

front rotors / calipers

all sold

  • 2 weeks later...

hey dont have one.

Set of Front LCA's gone

The rack/cross member that wasnt in the car has gone

1x power steering res gone

How much for f & r calipers, rotors, pads and lines and condition/type of all

Driveshafts

Rear brakes + hubs and knuckle

back section of handbrake cable

front rotors / calipers

all sold

no aftermarket dump pipe

i havent taken off the cable to open the petrol tank. i would have to check its condition for you though.

  • 3 weeks later...

ok the wreck has everything off it that i actually want/have sold. What ever is left on it is going super dirt cheap so if you can see anything tell me before it goes all together!

IMG_2986.jpg

IMG_2988.jpg

IMG_2987.jpg

IMG_2990.jpg

IMG_2989.jpg

IMG_2985.jpg

IMG_2991.jpg

IMG_2992.jpg

IMG_2994.jpg

all the panels are off the car now, make an offer!

IMG_2996.jpg

IMG_2997.jpg

still have the 18's and the 3.5" exhaust, manual tail shaft. Offers!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...