Jump to content
SAU Community

Recommended Posts

1990 R32 GTS-T

- 126,000 km

- 5spd manual

- Rb20det (very strong and healthy)

- Rego till July 2011

- Sunroof

- Full Bn blister widebody kit, (150 kg lighter than a stock R32)

- R34 front conversion

InSide:

- Drift guages, Water, Oil pres, Oil temp

- Cyber stalk dash cluster

- Pioneer head unit

- Kicker 15" Sub, Competition series

- Kicker amp

- Deep dish Drift steering wheel

ENGINE:

Approx 200kw at the wheels

- Hi flow turbo (very Responsive)

- Re mapped ECU, Tuned for up to 19psi but havn't gone past 15 due to injectors. will make 240kw with new injectors

- Turbo tech boost controller 10psi/15psi

- stock airbox. (Hks Pod inculded)

- 3" split dump pipe to 3" front pipe

- Kakimoto full exhaust. (not too loud)

- Front mount intercooler

- 42mm alloy radiator

Driveline:

- Hicas lock bar

- HD clutch (recent)

- Work Vs xx (very rare)

18x10 -12 offset rears (275x40x18)

18x9 -4 offset front (235x40x18)

Had this car for a long time now, Never missed a beat. Mechanically it is very strong. I would drive it to QLD tomorrow with no worries.

Good on fuel, Just under 500ks to a 50 liter tank. Always used BP ultimate.

Professinaly built by the guys at drift line with the intentions to be a show car. I bought this off them. They imported this car and im the second owner.

The bad: could use some TLC out side. bit of paint. Nothing major. This car is in great condition I drive it everyday. Just time for me to move on.

Interested in swaps so shoot some offers, stagea, legnum, r34, aristo, V8 ford / holden, road bike 250cc. Anything really. Nothing old though.

Spent so much money on this car =(

$8900

Link to comment
https://www.sau.com.au/forums/topic/349145-r32-gts-t-cheap-cheap-cheap/
Share on other sites

1991 jzz30 twin turbo soarer with mods new paint and tego and can supply rwc aswell

link to for sale thread on f sport

pics dont do car justice

ether

jzz30 1jz-gte

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • @Haggerty this is your red flag. In MAP based ECU's the Manifold pressure X RPM calculation is how the engine knows it is actually...running/going through ANY load. You are confusing the term 'base map' with your base VE/Fuel table. When most people say 'base map' they mean the stock entire tune shipped with the ECU, hopefully aimed at a specific car/setup to use as a base for beginning to tune your specific car. Haltech has a lot of documentation (or at least they used to, I expect it to be better now). Read it voraciously.
    • I saw you mention this earlier and it raised a red flag, but I couldn't believe it was real. Yes, the vacuum signal should vary. It is the one and only load signal from the engine to the ECU, and it MUST vary. It is either not connected or is badly f**ked up in some way.
    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
×
×
  • Create New...