Jump to content
SAU Community

Recommended Posts

Hi I am new to the site, and am currently working on a S13 240sx with an RB25 R34 NEO engine swap. Due to my turbo placement and intercooler piping setup i bought a Greddy "style" intake manifold. My question is what have others done to use the NEO's top feed style injectors with the Greddy style manifold. I made a bracket to physically relocate the fuel rail but there is considerable slop between the injector and the injector bung walls on the manifold. Looking for some ideas as to what others have done to make this combination work

OR....

Are there any cheap alternatives in terms of fuel rails or easy to source stock injectors from other models that may fit (keeping budget friendly in mind haha) I am in the states so r33 injectors and fuel rails dont pop up too often for sale.

Thank you! I have spent a lot of time searching for the answer but not a specific solution other than many people buying new rails and aftermarket injectors. Thanks!!

Edited by getslideways

I just got NEO fuel rail mounts rewelded to a position suitable for Greddy manifold. Costed ~20$.

Do you have any pics? If so it would be greatly appreciated! Also what did you end up using for injector o-rings/sealing rings? Thanks!

I made a bracket to relocate and space the NEO fuel rail and injectors that seems like it will work (still curious to see yours) but now need to make a good seal between the NEO injectors and the inside the intake manifold injector bung somehow, since there seems to be some slop and not air tight

thanks!

Edited by getslideways

or gtr rail and spacers. Use the rb25 rubber seals in manifold or get adapters.

http://www.skylinesaustralia.com/forums/topic/306527-r33-greddy-inlet-plenum-onto-a-rb25det-neo/page__hl__greddy+inlet+neo__st__20

I have done this conversion on my neo

Read my last post, item no.6

Edited by darrinspencer

Hey Darrin,

so theres no aftermarket fuel rails out there to accept the GTT/Stagea injectors?

i wanna do this but dont want to change my injectors.

When I set my imitation greddy manifold on my neo motor, I fitted factory gtt injectors and rail, by slotting the holes in the rail, and making a spacer. and got new O-rings that had thicker sidewalls. Fitted tight. cost 5 dollars from a local bearing supplier. Just make sure if you do do this they're up to withstanding fuel.

Hey Darrin,

so theres no aftermarket fuel rails out there to accept the GTT/Stagea injectors?

i wanna do this but dont want to change my injectors.

The aftermarket fuel rail (cheap chinese HKS copy) fits the injectors.

What the OP was asking was how to fit the neo injectors in the greddy manifold as the greddy is made for R33 side feed injectors.

All you do is keep the standard O ring on the bottom of the injector plus add the R33/S15 larger grommets to fill the manifold.

As long as you have enough clampping pressure on the rail they will seal

Status posted some pic's on here somewhere showing a close up.

The aftermarket fuel rail (cheap chinese HKS copy) fits the injectors.

What the OP was asking was how to fit the neo injectors in the greddy manifold as the greddy is made for R33 side feed injectors.

All you do is keep the standard O ring on the bottom of the injector plus add the R33/S15 larger grommets to fill the manifold.

As long as you have enough clampping pressure on the rail they will seal

Status posted some pic's on here somewhere showing a close up.

Cheers for that,

so these would fit my neo motor? Some say " Single entry single return configuration", my rail has 2 regs, can i still use both regs

http://cgi.ebay.com/ebaymotors/R32-R33-R34-GTS-BILLET-INJECTOR-FUEL-RAIL-RB25DET-RB25-_W0QQcmdZViewItemQQhashZitem3363e700ebQQitemZ220719415531QQptZMotorsQ5fCarQ5fTruckQ5fPartsQ5fAccessories

Cheers for that,

so these would fit my neo motor? Some say " Single entry single return configuration", my rail has 2 regs, can i still use both regs

http://cgi.ebay.com/ebaymotors/R32-R33-R34-GTS-BILLET-INJECTOR-FUEL-RAIL-RB25DET-RB25-_W0QQcmdZViewItemQQhashZitem3363e700ebQQitemZ220719415531QQptZMotorsQ5fCarQ5fTruckQ5fPartsQ5fAccessories

That is exactly what I used, but I did away with twin factory reg's and fitted a Sard one, even thuo I did not really need and adjustable one with the siemen 650cc injectors I used.

Just be away of the cheap copies. I had fuel leaking from both ends and had to get the end re machined square to seal.

I may just have got a dud one which is not unusual for cheap chinese crap.

Can buy genuine HKS but $300++

Do you have any pics? If so it would be greatly appreciated! Also what did you end up using for injector o-rings/sealing rings? Thanks!

I made a bracket to relocate and space the NEO fuel rail and injectors that seems like it will work (still curious to see yours) but now need to make a good seal between the NEO injectors and the inside the intake manifold injector bung somehow, since there seems to be some slop and not air tight

thanks!

Sorry for delay, didn't see your message.

I used slightly fatter than factory lower o-rings + some kind of hard rubber for bigger manifold o-rings, I don't know how to properly call this part. Installation is somewhat messy, but there is no vacuum/boost leak, so it all works for me. I'm currently using factory injectors, so I didn't use any spacer for a rail.

As for pics, I'll try to arrange that in a week.

Edited by Legionnaire

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Sounds like you've got an interesting adventure ahead here with local support if you have trouble! My guess is that, unboosted, you will be OK with a small upgrade like -9. What will happen is that once the stock ECU sees more airflow than it expects it will add a heap of fuel and pull a heap of timing to be safe because it can't understand how it could get that much air without there being an issue. You will see clouds of black smoke and it won't pull hard through the midrange and top end. So, overall it will be a bit frustrating but should be OK. If you are still nervous set the base timing back 2o through the CAS, but it will be even more sluggish everywhere. As said above through...this is not my guarantee your engine won't be blown into a million pieces, leaving you looking for very hard to find parts A better idea is get a computer with logging ASAP, wire in a wide band O2 sensor and a use remote tuner. I've done multiple cars this way and while it is not as good as a specific tune on a dyno they can get it 90% right. I'd suggest if you can afford an R33 GTR these days you can afford an ECU and tune. And if you can't afford that you sure won't be able to afford the rebuild if it goes bad in the meantime,.  
    • Yeah it would be nice if someone took the time to put that sort of information together, but there are a lot of variations in looms. I think you are making this way hard for yourself if you just want to get it running....sourcing an SR20 with the right wiring will be a billion times easier than matching the RB loom to an S15 chassis. If you do end up going this way, you just need to trace every wire in the loom with a multimeter, 95% of them will go to a location you can confirm at the ECU.....and then post it up for the next person who needs it  
    • Just top it up with water, and keep a general idea of how much you added. It is normal for water to be pushed into and pulled out of the reservoir through the cap, and it should not be more than half full or it will be likely to overflow when hot. Any decent mechanic can do a pressure test of the cooling system to confirm if you have a leak. Keep in mind if it is only leaking a little and when hot it may well evaporate before you see it hit the ground
    • I'd ask the shop what they used and use that. Mixing coolants is sometimes OK, sometimes not, and you have know the details of each coolant to know whether it's a good idea or not.
    • Is it alright to top up with just another green coolant?
×
×
  • Create New...