Jump to content
SAU Community

R34 Parts

skyline_r33_panda
 Share

Recommended Posts

skyline_r33_panda Community Regular

skyline_r33_panda

Posted
Posted

R34 PARTS...THE BODY IS AT THE SCRAP YARD AND THIS IS WHAT'S LEFT

OPEN TO OFFER BECAUSE I WANNA CLEAR THE YARD WILL SWAP PARTS I HAVE FOR SALE

FOR THE ITEM'S LISTED AT THE BOTTOM OF THE PAGE.

>DUMP PIPE (ADVANCED) $80

>AIR BAR STEERING WHEEL $150(MANUAL)

>DRIVERSIDE DOOR WITH GLASS $250

>DRIVERSIDE MIRROR $50

>REAR WINDOW (REMOVED) $150

>DRIVERS DOOR TRIM $100 (HAS WINDOW SWITCH STILL)

>R34 STOCK AIR BOX DAMAGED $50 (ONE CORNER & ONE TAB)$50

>A/C COMPRESSER $100

>A/C CONDENSER $50

>ABS MODULE $100

>BRAKE MASTER $150

>DIFF $200

>REAR BRAKES COMPLETE $400 AS IN PIC)

(lower control arm is bent on one side)

>TAILSHARFT $100

>CLUTCH MASTER $50

>PEDALS $100

>HAND BRAKE HANDLE $50(WITH FRONT CABLE)

>STOCK STRUT BRACE FRONT $25

>IGNITION BARRAL/DOOR/BOOT LOCKS AND A KEY $100

>R34 FRONT CROSSMEMBER $150

>BONNET CABLE/LATCH AND HORN PEICE $50

>R34 CASTOR RODS STOCK $50PAIR

>SR20DET 5 SPEED GEARBOX GOOD CONDITION $350

>HIGH FLOW CAT $100

>Vertex Body Kit to suit lancer 96-03 Coupe (full kit) $500

>DECAT PIPE $50

AND THESE ARE THE ARTS I NEED AND AM WILLING TO SWAP PARTS PLUS CASH FOR THEM..OR IF YOU HAE THESE PARTS CHEAP PM ME.

SR20DET RED TOP/S13 SILVIA

1.GREDDY PULLEY KIT (MOST IMPORTANT AND URGENT)

2.GREDDY/HKS CAMS

3.HKS FUEL RAIL

4.NISMO FPR

5.550CC INJECTORS

6.S13 BN BODY KIT......FRONT / SIDES / REAR

Link to comment
https://www.sau.com.au/forums/topic/349323-r34-parts/
Share on other sites
  • 1 month later...
Zaver Experienced

Zaver

Posted
Posted

Hey buddy, im after some parts for an R34, here's a link to what i need so if u have them do let me know.. -> http://www.skylinesaustralia.com/forums/topic/355141-r34-gtt-rear-seat-belt-and-front-indicator-holder/

Cheers

Link to comment
https://www.sau.com.au/forums/topic/349323-r34-parts/#findComment-5694622
Share on other sites
  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      NC MX5

      By Dose Pipe Sutututu · Posted

      Lamb roast on Saturday will be different 🥲
    • TurboTapin
      RB25DET with solid lifters - which cams ?

      By TurboTapin · Posted

      They are under bucket shims. Tomei provides a test shim kit and then any measurement of shim required. 
    • GTSBoy
      RB25DET with solid lifters - which cams ?

      By GTSBoy · Posted

      I always wondered how you were supposed to buy a set of 24 buckets and somehow magically have every single one of them yield exactly the desired clearance. I would have thought you'd need to assemble a cam with either 12 "sample" or "example" buckets of known top thickness (or a single such sample/example 12 times over!!) measure clearances at every valve, and then do the usual math to work out what the actual "shimness" of each bucket needed to be, before buying the required buckets to make up he thicknesses that you didn't have on hand.
    • TurboTapin
      RB25DET with solid lifters - which cams ?

      By TurboTapin · Posted

      I now seem to be limited in power due to my rev limit/hydraulic lifters in my built RB25. I'm looking into converting over to Tomei solid lifters. Question for anyone that has done the conversion. I was always under the impression that when using the Tomei solid lifter conversion, you would also require new valves (Longer or shorter stems, I can't remember which).  I don't know where I got this idea, as so far I see no mention of this in any of the Tomei documentation. It just states I need the Tomei solid buckets, solid lifter cams and upgraded springs. As my head is already built, all I would need is another set of 1000$ Kelford cams, 500$ buckets and about 4H hours of my time installing and I'm off to the races!?!? There's no way it's that simple, I must be missing something? 
    • TurboTapin
      Why am I hitting a power wall with my stroked RB25?

      By TurboTapin · Posted

      I couldn't agree more. I should have started from the get-go with a NEO or solid bucket conversion. I started looking into converting over to solid lifters yesterday. Now for some reason I was always under the impression that when using the Tomei solid lifter conversion, you would also require new valves (Longer or shorter stems, I can't remember which).  But I see no mention of this on any of the Tomei documentation. It just states that I need the Tomei solid buckets, solid lifter cams and upgraded springs. As my head is already built, all I would need is another set of 1000$ Kelford cams, 500$ buckets and about 4H hours of my time installing and I'm off to the races!?!? There's no way it's that simple, I must be missing something? 
×
×
  • Create New...