Jump to content
SAU Community

Recommended Posts

whilst they are interchangle and the car will start etc

some MEC chip types are not, you may find if you get the wrong MEC chip type, the car runs OK and idles etc but as soon as you drive it, it becomes mega sluggish and performs like ASS

i had this on my series 2 GTST with a remapped ECU, the remap was done to suit basic mods and i connected it up, took it for a spin and it ran like a bucket of crap

turns out the MEC chip type was wrong and i had to use a different MEC chip number. ask a remapper what the MEC chip type means, from memory the guy in sydney taso i think knows what it means

Your mines ecu will probably have the speed limiter removed (all JDM cars are limited to 180km/hr) and be tuned differently from stock.

Are you planning to get a Nistune?

If the answer is yes then it may be possible to take out the Mines chip from your ecu and replace it with the Nistune chip (or it may be glued in too securely).

If the answer is no then ideally you would put your car on a dyno and do a run with the Mines ecu and then a stock ecu and keep the most suitable one.

Your mines ecu will probably have the speed limiter removed (all JDM cars are limited to 180km/hr) and be tuned differently from stock.

Are you planning to get a Nistune?

If the answer is yes then it may be possible to take out the Mines chip from your ecu and replace it with the Nistune chip (or it may be glued in too securely).

If the answer is no then ideally you would put your car on a dyno and do a run with the Mines ecu and then a stock ecu and keep the most suitable one.

Its different from stock, i emailed Mines and asked what they had done to it.

I would like to get a nistune, but i also want to be able to control all the stuff and aftermarket ecu's do that, but i am leaning towards a nistune due to the shear price, and if i give my fiance 2 options she would chose the cheaper option allowing me to get it sooner.

If i get a nistune and cant take the chip out of my mines i am screwwed, so i guess ill have a spare one ready to get chipped and put in and tuned

From memory the MEC number Paul is going in about is the type of chip in the ECU. so like he said you may have trouble putting say a MEC123 chip into an ECU board that is designed/programmed to read a MEC987 chip. The reason people swap just chips around is to reflash the tune, you pull the old chip out and install a new one with a tune burnt on it. It makes sense when doing this to keep the chip types the same.

Because your looking at using the whole ecu you should be ok using either the 0V800 or 0V801. I'm certain there wasn't any changes in sensor types or wiring between the 98-99 run of ecu's (800) and the 99-on (801). also, either ecu is able to be nistuned.

I know it's a different car but still a RB Nissan, I ran a 89 ecu in my 92 R32 without an issue.

Edit: should also add that the 89 ecu had a different MEC number to the original 92 ecu and I had no issues.

Edited by QWK32

Buy the nistune chipped ecu from KJB-R33. It will almost certainly work and if by some chance it doesn't you could always on sell it - its only the price of the Nistune chip anyway you could always take that out and it would be worth the price.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...