Jump to content
SAU Community

Recommended Posts

I just found out today because my car is an automatic,it'd cost around $3,500.00 to remap or install the new piggyback ECU or something ? Not really sure.

someones taking you for a ride...

just go with a nistune board. install.. remap and away you go

  • Replies 53
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

What will the NISTUNE do to my car exactly ? Sorry I'm not really familiar with this kind of things as I never had a turbocharged car before lol.

Edited by Jeremy1607

What will the NISTUNE do to my car exactly ? Sorry I'm not really familiar with this kind of things as I never had a turbocharged car before lol.

In this case I would be either doing a lot of reading on here, or just find someones setup that you like and copy their setup and take it to the same tuner (obviously must be local to you and run an automatic gearbox).

What will the NISTUNE do to my car exactly ? Sorry I'm not really familiar with this kind of things as I never had a turbocharged car before lol.

It is like getting a full aftermarket ECU as it lets you retune ignition and fuel maps in real time as well as tweak some other things.

Well I think the 230kw figure is a load of crap and I doubt with a stock ecu you are making over 180, so normally you'd see ~200 with the neo turbo. It is also a required upgrade before you can do anything else, can't go bigger turbo or change injectors without it.

Should see better economy and smoother acceleration definitely thoug, really need to see what it is like on the dyno now to see how much of an improvement there can b, some look worse than others and have a huge dip in the midrange due to it richening up.

Edited by Rolls

yep, i had my ecu remapped with a nisstune and it cost me $650.... and that was an auto ecu in a manual conversion

Yeah,I asked Imports 101 and they said they'd charge $1,500.00 for the Nistune,fitted,tuned and tested ? How come it's expensive compared to other workshop ?

Also regarding lowering the car with king springs,here in Perth Ian Diffen or Tech 9 Tyres can do them for $500 fitted but Imports 101 said they can do it for $750 fitted ?

Is it good service or a rip off ? Where did you do yours ?

Thanks.

Edited by Jeremy1607

They also said that I will need boost valve bleed or something for $130 fitted or a good controller for $750 fitted ? Altogether you'd be looking for $2,000.00 ?

Usually for the Nistune drive in drive out with a tune shouldn't be more than $750, i think $1500 is a bit steep for it, Instead u can get a power FC + Tune for around $1700.. I suggest you check around other places for the Nistune because its great bang for buck!!

Yeah,I asked Imports 101 and they said they'd charge $1,500.00 for the Nistune,fitted,tuned and tested ? How come it's expensive compared to other workshop ?

Also regarding lowering the car with king springs,here in Perth Ian Diffen or Tech 9 Tyres can do them for $500 fitted but Imports 101 said they can do it for $750 fitted ?

Is it good service or a rip off ? Where did you do yours ?

Thanks.

Ring around, that is steep even if they are great tuners. A boost controller is not needed for stock turbo, an exhaust will cause it to run 10-12psi anyway with an rb20 actuator.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
×
×
  • Create New...