Jump to content
SAU Community

Helpl Boost Prob

Pottsy12

By Pottsy12,
in Engines & Forced Induction

 Share

Recommended Posts

Rolls Grand Master

Rolls

Posted
Posted

Wait... Something is wrong then, I think mine will even open gate on high boost in 1st gear! That's 26psi :)

Will test with some videos tonight and see what I actually get.

probably starts to crack the gate but no way 26psi haha, I'd say 15 ish absolute max.

SimonR32 Grand Master

SimonR32

Posted
Posted

Shit I forgot to test!

Yeah might not hit that much, really depends on trye grip as well... If it wheel spins your not going to be as much boost, if you launch of limiter with drag slicks I'd imagine it would a lot of boost fast :)

Will try and remember again tonight haha

Harey Veteran

Harey

Posted
Posted

Yes but I was giving an example of how the turbo behaves respective of load. Not wether or not it will stay consistent if it reaches it's boost level. I felt it was a better example then saying you won't hit target boost in neutral (unless maybe your on limiter) as opposed to flat to the floor in third. The hill thing was just an easier comparison of load.

OP: read the manual to see if what I have said in my last post is in there and if it says the reason behind doing that mod. Might be for boost creep rather then your problem I forget. Otherwise I'd try putting stock parts bak on to trial (BOV and boost solenoid mainly) if it starts working then it will show you your problem

Yup sorry, I agree with what your saying just didnt want people to expect different boost levels in different gears with a well setup actuator/boost control system. You are 100% correct its easier to build boost with more load.

SimonR32 Grand Master

SimonR32

Posted
Posted

probably starts to crack the gate but no way 26psi haha, I'd say 15 ish absolute max.

Got 1.38bar on the first attempt and 1.43bar on the second... Will upload the video when I have time :)

Don't know how people are only getting 0.3bar in first with a GT30, something must have been wrong!

SimonR32 Grand Master

SimonR32

Posted
Posted

20psi, in first gear with a GT30 on a RB25?

ok. Now I have seen it all.

Post a video or I call 110% bullshit.

yeah good call......

the only that you be possible is if you had the hand brake on to load it up :rofl2:

I could make a max of 5psi in first, nothing more. WIth a GT30 and 0.63 rear.

OP needs to look at if the wastegate is holding shut. Or put tension on it.

tow a boat up a hill in 1st gear, probably could hit 20psi :whistling:

Hows the foot in mouth tasting?!?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • bilbo117
      R34 GTR Seats / No longer reclining

      By bilbo117 · Posted

      Hi all, Long time since I've posted here. Looking for some advice on what I can remove to further identify the cause of my issues.  I can move the passenger seat forward and back but the knob used to adjust the seat angle is pretty much free spinning, there's very little resistance.  Removing the side cover I can see that the chain is intact but the shaft for the adjustment spins without the gear attached to it moving.  What's my next step for disassembly here? Is this a common fault? Just being a little cautious as I didn't want to start removing bolts for a spring to fly out or something equally as stupid.  Cheers
    • Dose Pipe Sutututu
      Ethanol Content Sensor - Always at 11%?

      By Dose Pipe Sutututu · Posted

      Those above shitboxes, mediocre and above usually have a turbo strapped to them, hence the slightly higher octane is required.  
    • sinn3r
      R34 Skyline climate control unit transistor

      By sinn3r · Posted

      Hi all,   long time listener, first time caller   i was wondering if anyone can help me identify a transistor on the climate control unit board that decided to fry itself   I've circled it in the attached photo   any help would be appreciated
    • Kinkstaah
      Blue slip

      By Kinkstaah · Posted

      I mean, I got two VASS engineers to refuse to cert my own coilovers stating those very laws. Appendix B makes it pretty clear what it considers 'Variable Suspension' to be. In my lived experience they can't certify something that isn't actually in the list as something that requires certification. In the VASS engineering checklist they have to complete (LS3/NCOP11) and sign on there is nothing there. All the references inside NCOP11 state that if it's variable by the driver that height needs to maintain 100mm while the car is in motion. It states the car is lowered lowering blocks and other types of things are acceptable. Dialling out a shock is about as 'user adjustable' as changing any other suspension component lol. I wanted to have it signed off to dissuade HWP and RWC testers to state the suspension is legal to avoid having this discussion with them. The real problem is that Police and RWC/Pink/Blue slip people will say it needs engineering, and the engineers will state it doesn't need engineering. It is hugely irritating when aforementioned people get all "i know the rules mate feck off" when they don't, and the actual engineers are pleasant as all hell and do know the rules. Cars failing RWC for things that aren't listed in the RWC requirements is another thing here entirely!
    • GTSBoy
      Best place to order Authetic R32 Parts in Japan

      By GTSBoy · Posted

      I don't. I mean, mine's not a GTR, but it is a 32 with a lot of GTR stuff on it. But regardless, I typically buy from local suppliers. Getting stuff from Japan is seldom worth the pain. Buying from RHDJapan usually ends up in the final total of your basket being about double what you thought it would be, after all the bullshit fees and such are added on.
×
×
  • Create New...