Jump to content
SAU Community

Recommended Posts

As title states. Engine is currently in my car and can be driven/seen running. Was rebuilt a few years ago and then mothballed, and has been started every 3 months since. The entire engine has done around 5000km, it's basically only just run in.

It's a series 1 RB25DE head grafted onto a series 1 RB30 block which has had the oil feed and returns tapped in to the block (so it is now identical to a series 2 block). The head was fully reconditioned, with new valve seats, springs etc etc etc, basically a full job. The bottom end was built with Clevite 77 rod bearings and genuine Nissan main bearings. The pistons are ACL cast pistons and the rods are standard items that have been beam polished and shot peened.

Essentially:

Engine;

RB25/30, fully rebuilt head and bottom end, everything has done about 5000km since rebuild with no issues. No blowby, no oil usage or leaks, a very tight engine.

Parts list:

3ltr block

ACL cast pistons, standard bore size, ACL race series rings.

Rods - standard. Crack tested, cryo treated, beam polished then shot peened.

Bearings: Nissan mains, clevite 77 rods.

R32 GTR oil pump.

R33 RB25DE head

fully rebuilt, new valve guides, reseated valves etc

stock cams

RB25DET 380cc injectors

This setup made 235rwkw on my twincharged setup, so it's quite well set up. The timing belt setup uses two tensioners on the high edge of the block so it's easier to adjust the tension on the slack and tight sides independently. The head was welded and faced to delete the VCT function, and a grub screw setup was put in the front intake cam bearing to supply oil to the front cam journal. The VCT is therefore disabled.

For extra cost I can supply my twincharge hotside and a JD custom plenum setup for the intake, but most likely I will sell that stuff separately.

Price: $2500

For that you get the block + head assembled, the oil pump and cam drive setup, rocker covers, spark plugs, cams etc all ready to go.

Location: inner north melbourne.

Pickup only. Happy to start car and allow buyer to listen to engine and inspect for leaks, smoke etc - there is none, this engine is mint. I will take half deposit, then remove engine for the buyer within 2 weeks.

Link to comment
https://www.sau.com.au/forums/topic/350728-fs-vic-full-rb2530-long-engine/
Share on other sites

hmmmm could be tough - she's not exactly light! I could probably find a pallet and strap it to that, but I'm unsure if I can get a courier to pick it up from my door, you'd need a forklift or something

If you know a way to do it easily then I can definately freight it, but I'd much prefer pickup because it's farkin heavy

bump - engine is coming out next weekend, so if you're interested in seeing it run before then, please pm me. otherwise take my word for it that it's good.

This engine made 235rwkw in my VL on 9psi, so it's pretty well set up. Quench is 35 thou. Power output only limited by the RB30 rods which are good for up to 300-320rwkw. Change the rods over to some cheap Spool rods or similar and it will be good for a LOT more power.

Price drop to $2300 if you put a deposit on it next week

The powerFC that ran this engine is now gone, so you can't see it running. Russman saw and heard it run when he picked the ECU so he can vouch for the fact that it didn't blow smoke or knock.

Engine is coming out this weekend.

Got 3 interested buyers, first person to put cash in my hand gets it

  • 2 months later...
  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...