Jump to content
SAU Community

Help With Sound System Setup

Guest

By Guest,
in Car Audio & Electrical

 Share

Recommended Posts

Guest

Guest

Posted
Posted

Hi,

I have decided to get a sound system for my r34, and am in need of a few questions to be answered.

I have decided to get a full alpine setup:

INA-W900E (Headunit)

SPX-17 PRO (Front speakers)

SPR-17C (Rear speakers)

PDX-1.1000 (Amp for sub)

PDX-4.150 (Amp for speakers)

The first question is will the front speakers fit into the door without mods, and will the rears fit without mods?

The second is, will having rear speakers have much difference with this setup, or should I just stay with the stock ones?

The third question is should I get one sub or two?

And finally, when I have the aforementioned sub, will I need the two amps mentioned or just run everything on the 4 channel amp?

Thanks guys,

Jacob

Link to comment
https://www.sau.com.au/forums/topic/350852-help-with-sound-system-setup/
Share on other sites
R33_KRAZY Rising Star

R33_KRAZY

Posted
Posted

having better that stock speakers in the back will deffinately enhance your sound quality.. run all your in car speakers of the 4 channel amp.. you will need a seperate amp for sub(s) as the 4 channel amp wont have the required LPF and you will destroy them.. also one amp will do fine for 2 subs but your best bet is just buy one decent sub an still have boot space.. i made 142Db with one 12' sub and a 800wrms amp.. not running at max levels either

Carbon 34 Grand Master

Carbon 34

Posted
Posted

this is something to consider to save some dosh, alpines offer on type x

alpine au

and yes if installed by a pro it will fit, they need mdf mounts to be solid in the doors

a little dynamat type soundeadner would be advised at least in the doors

ditch the stock speakers in all cases

run the 4 channel to the 4 inside

mono block to subs

enjoy

Antonio_Waxit Collaborator

Antonio_Waxit

Posted
Posted

Hi Jacob,

I used to work in the Car Audio Industry, try Ang's Audio Shop in Klemzig http://www.angs.com.au/ . He is an Alpine dealer and will be able to help you out. You should be able to find all of those products in your vehicle. Its also best to get custom MDF baffle made for the speakers in the front rather than the standard plastic ones as you have much clearing mid base as well as improved sealing the speaker enclosure (inner door).

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • djr81
      RB26DETT Sketchy boost mod?

      By djr81 · Posted

      Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
    • PranK
      Chris' Toyota Mark ii JZX110

      By PranK · Posted

      This looks great! Awesome to have the 5 speed with an LSD in this. The Recaro's look like SR2's or SR3's. It's a shame they've been retrimmed as they would have looked sweet in their original colours. I think I'd want my agent to be a little more up front and informative too. I've never imported but I reckon it would make me a little nervous, so the more info the better.
×
×
  • Create New...